- 您現在的位置：買賣IC網 > PDF目錄11829 > SC16C850LIET,118 (NXP Semiconductors)IC UART SGL W/FIFO 36TFBGA PDF資料下載
參數資料
| 型號： | SC16C850LIET,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 26/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SGL W/FIFO 36TFBGA |
| 標準包裝： | 4,000 |
| 特點： | 可編程 |
| 通道數： | 1，UART |
| FIFO's： | 128 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.5V |
| 帶并行端口： | * |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-TFBGA |
| 供應商設備封裝： | 36-TFBGA（3.5x3.5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
32 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
7.14 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register.
Bits 0 through 4 provide single or dual character software flow control selection. When the
Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words are
concatenated into two sequential numbers.
[1]
Enhanced function control bits IER[7:4], ISR[5:4], FCR[5:4] and MCR[7:5].
Table 23.
Enhanced Feature Register bits description
Bit
Symbol
Description
7
EFR[7]
Automatic CTS flow control.
logic 0 = automatic CTS flow control is disabled (normal default condition)
logic 1 = enable automatic CTS flow control. Transmission will stop when
CTS goes to a logical 1. Transmission will resume when the CTS pin returns
to a logical 0.
6
EFR[6]
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow
control. RTS functions normally when hardware flow control is disabled.
logic 0 = automatic RTS flow control is disabled (normal default condition)
logic 1 = enable automatic RTS flow control
5
EFR[5]
Special Character Detect.
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C850 compares each
incoming receive character with Xoff2 data. If a match exists, the received
data will be transferred to FIFO and ISR[4] will be set to indicate detection of
special character. Bit 0 in the X-registers corresponds with the LSB bit for the
receive character. When this feature is enabled, the normal software flow
control must be disabled (EFR[3:0] must be set to a logic 0).
4
EFR[4]
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the enhanced
registers, EFR[4] can be set to a logic 0 to latch the new values. This feature
prevents existing software from altering or overwriting the SC16C850 enhanced
functions.
logic 0 = disable/latch enhanced features[1]. (Normal default condition.)
logic 1 = enables the enhanced functions[1].
3:0
EFR[3:0]
Cont-3:0 TX, RX control. Logic 0 or cleared is the default condition.
Combinations of software flow control can be selected by programming these
bits. See Table 24.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B7H-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
| VE-B7H-IW-F3 | CONVERTER MOD DC/DC 52V 100W |
| VI-BWZ-IW | CONVERTER MOD DC/DC 2V 40W |
| VE-B7H-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| AT32UC3L032-ZAUR | IC MCU AVR32 32K FLASH 48VQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C850LIET-G | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850LIET-S | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850SV | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 20 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C850SVIBS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 20 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C850SVIBS,115 | 功能描述:UART 接口集成電路 UART 1-CH 128Byte FIFO 1.8V 32-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。