參數資料
型號： SC16IS760IPW
廠商： NXP Semiconductors N.V.
元件分類： 連接器件
英文描述： Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
封裝： SC16IS740IPW/Q900<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.html<1<Always Pb-free,;SC16IS740IPW<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.
文件頁數： 17/62頁
文件大?。?/td> 308K
代理商： SC16IS760IPW
SC16IS740_750_760_6
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 13 May 2008
17 of 62
NXP Semiconductors
SC16IS740/750/760
Single UART with I
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
7.6 Sleep mode
Sleep mode is an enhanced feature of the SC16IS740/750/760 UART. It is enabled when
EFR[4], the enhanced functions bit, is set and when IER[4] is set. Sleep mode is entered
when:
The serial data input line, RX, is idle (see
Section 7.7 “Break and time-out
conditions”
).
The TX FIFO and TX shift register are empty.
There are no interrupts pending except THR.
Remark:
Sleep mode will
not
be entered if there is data in the RX FIFO.
In Sleep mode, the clock to the UART is stopped. Since most registers are clocked using
these clocks, the power consumption is greatly reduced. The UART will wake up when any
change is detected on the RX line, when there is any change in the state of the modem
input pins, or if data is written to the TX FIFO.
Remark:
Writing to the divisor latches, DLL and DLH, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLH.
7.7 Break and time-out conditions
When the UART receives a number of characters and these data are not enough to set off
the receive interrupt (because they do not reach the receive trigger level), the UART will
generate a time-out interrupt instead, 4 character times after the last character is
received. The time-out counter will be reset at the center of each stop bit received or each
time the receive FIFO is read.
A break condition is detected when the RX pin is pulled LOW for a duration longer than
the time it takes to send a complete character plus Start, Stop and Parity bits. A break
condition can be sent by setting LCR[6]. When this happens the TX pin will be pulled LOW
until LSR[6] is cleared by the software.
7.8 Programmable baud rate generator
The SC16IS740/750/760 UART contains a programmable baud rate generator that takes
any clock input and divides it by a divisor in the range between 1 and (2
16
– 1). An
additional divide-by-4 prescaler is also available and can be selected by MCR[7], as
shown in
Figure 14
. The output frequency of the baud rate generator is 16
×
the baud rate.
The formula for the divisor is given in
Equation 1
:
(1)
where:
prescaler = 1, when MCR[7] is set to ‘0’ after reset (divide-by-1 clock selected)
prescaler = 4, when MCR[7] is set to ‘1’ after reset (divide-by-4 clock selected).
Remark:
The default value of prescaler after reset is divide-by-1.
divisor
prescaler
desired baud rate
------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------
16
×
=
相關PDF資料
PDF描述
SC16IS741IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IPW Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS762IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS762IPW Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
相關代理商/技術參數
參數描述
SC16IS760IPW,112 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW,128 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW112 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
SC16IS760IPW-F 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW-S 功能描述:IC UART I2C/SPI 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*