參數資料
型號： SC16IS760IPW
廠商： NXP Semiconductors N.V.
元件分類： 連接器件
英文描述： Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
封裝： SC16IS740IPW/Q900<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.html<1<Always Pb-free,;SC16IS740IPW<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.
文件頁數： 9/62頁
文件大?。?/td> 308K
代理商： SC16IS760IPW
SC16IS740_750_760_6
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 13 May 2008
9 of 62
NXP Semiconductors
SC16IS740/750/760
Single UART with I
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
[3]
HVQFN24 package die supply ground is connected to both V
SS
pins and exposed center pad. V
SS
pins must be connected to supply
ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be
soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias
need to be incorporated in the PCB in the thermal pad region.
7.
Functional description
The UART will perform serial-to-I
2
C conversion on data characters received from
peripheral devices or modems, and I
2
C-to-serial conversion on data characters
transmitted by the host. The complete status the SC16IS740/750/760 UART can be read
at any time during functional operation by the host.
The SC16IS740/750/760 can be placed in an alternate mode (FIFO mode) relieving the
host of excessive software overhead by buffering received/transmitted characters. Both
the receiver and transmitter FIFOs can store up to 64 characters (including three
additional bits of error status per character for the receiver FIFO) and have selectable or
programmable trigger levels.
The SC16IS740/750/760 has selectable hardware flow control and software flow control.
Hardware flow control significantly reduces software overhead and increases system
efficiency by automatically controlling serial data flow using the RTS output and CTS input
signals. Software flow control automatically controls data flow by using programmable
Xon/Xoff characters.
The UART includes a programmable baud rate generator that can divide the timing
reference clock input by a divisor between 1 and (2
16
– 1).
7.1 Trigger levels
The SC16IS740/750/760 provides independently selectable and programmable trigger
levels for both receiver and transmitter interrupt generation. After reset, both transmitter
and receiver FIFOs are disabled and so, in effect, the trigger level is the default value of
one character. The selectable trigger levels are available via the FCR. The programmable
trigger levels are available via the TLR. If TLR bits are cleared then selectable trigger level
in FCR is used. If TLR bits are not cleared then programmable trigger level in TLR is used.
7.2 Hardware flow control
Hardware flow control is comprised of auto CTS and auto RTS (see
Figure 8
). Auto CTS
and auto RTS can be enabled/disabled independently by programming EFR[7:6].
With auto CTS, CTS must be active before the UART can transmit data.
Auto RTS only activates the RTS output when there is enough room in the FIFO to receive
data and de-activates the RTS output when the RX FIFO is sufficiently full. The halt and
resume trigger levels in the TCR determine the levels at which RTS is
activated/deactivated. If TCR bits are cleared then selectable trigger levels in FCR are
used in place of TCR.
If both auto CTS and auto RTS are enabled, when RTS is connected to CTS, data
transmission does not occur unless the receiver FIFO has empty space. Thus, overrun
errors are eliminated during hardware flow control. If not enabled, overrun errors occur if
the transmit data rate exceeds the receive FIFO servicing latency.
相關PDF資料
PDF描述
SC16IS741IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IPW Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS762IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS762IPW Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
相關代理商/技術參數
參數描述
SC16IS760IPW,112 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW,128 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW112 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
SC16IS760IPW-F 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW-S 功能描述:IC UART I2C/SPI 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*