- 您現在的位置：買賣IC網 > PDF目錄16517 > SI3220PPT0-EVB (Silicon Laboratories Inc)BOARD EVAL W/SI3200 INTERFACE PDF資料下載
參數資料
| 型號： | SI3220PPT0-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 66/112頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL W/SI3200 INTERFACE |
| 標準包裝： | 1 |
| 系列： | ProSLIC® |
| 主要目的： | 接口，模擬前端（AFE） |
| 已用 IC / 零件： | Si3220 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
Si3220/25 Si3200/02
Rev. 1.3
57
Not
Recommended
fo
r N
ew
D
esi
gn
s
The Si3220 can also add a dc offset component to the
ringing signal and detect a ring trip event by monitoring
the dc loop current flowing once the terminal equipment
transitions to the off-hook state. Although adding dc
offset reduces the maximum available ringing amplitude
(using the same ringing supply), this method is required
to reliably detect a valid ring trip event when sourcing
longer loop lengths. The dc offset can be programmed
from 0 to 64.32 V in the RINGOF RAM address as
required to produce adequate dc loop current in the off-
hook state. Depending on the loop length and the ring
trip method, the ac or dc ring trip detection circuits are
disabled by setting their respective ring trip thresholds,
RTACTH or RTDCTH, sufficiently high so that they do
not trip under any condition.
3.15.5. Si3225 Ring Trip Detection
The Si3225 implements an external ring trip detection
scheme when using a standard battery-backed external
ringing generator. In this application, the centralized
ringing generator produces an unbalanced ringing
signal that is distributed to individual TIP/RING pairs. A
per-channel ringing relay is required to disconnect the
Si3225 from the TIP/RING pair and apply the ringing
signal. By monitoring the ringing feed path across a ring
series with the ringing source, the Si3225 can detect the
dc current path created when the hook switch inside the
terminal equipment closes. The internal ring trip
detection circuitry is identical to that illustrated in
Figure 27. Figure 31 illustrates the typical external ring
trip circuitry required for the Si3225. Because of the
long loop nature of these applications, a dc ring trip
detection scheme is typically used. The user can
disable the ac ring trip detection circuitry by setting the
RTACTH threshold sufficiently high so it does not trip
under any condition.
3.16. Relay Driver Considerations
The Dual ProSLIC devices include up to three
dedicated relay drivers to drive external ringing and/or
test relays. Test relay drivers TRD1a, TRD1b, TRD2a,
and TRD2b are provided in all product versions, and
ringing relay drivers RRDa and RRDb are included for
the Si3225 only. In most applications, the relay can be
driven directly from the Dual ProSLIC with no external
relay drive circuitry required. Figure 28 illustrates the
internal relay driver circuitry using a 3 V or 5 V relay.
Figure 28. Dual ProSLIC Internal Relay Drive
Circuitry
The internal driver logic and drive circuitry are powered
by the same VDD supply as the chip’s main VDD supply
(VDD1–VDD4 pins). When operating external relays from
a VCC supply equal to the chip’s VDD supply, an internal
diode network provides protection against overvoltage
conditions from flyback spikes when the relay is
opened. Either 3 V or 5 V relays can be used in the
configuration shown in Figure 28, and either polarized
or non-polarized relays are acceptable if the VCC and
VDD supplies are identical. The input impedance, RIN, of
the relay driver pins is a constant 11
while sinking
less than the maximum rated 85 mA into the pin.
If the operating voltage of the relay (VCC) is higher than
the Dual ProSLIC VDD supply voltage, an external drive
circuit is required to eliminate leakage from VCC to VDD
through
the
internal
protection
diode.
In
this
configuration, a polarized relay will provide optimal
overvoltage
protection
and
minimal
external
components. Figure 29 illustrates the required external
drive circuit, and Table 32 provides recommended
values for RDRV for typical relay characteristics and VCC
supplies. The output impedance, ROUT, of the relay
driver pins is a constant 63
while sourcing less than
the maximum rated 28 mA out of the pin.
Si3220/
Si3225
Relay
Driver
Logic
V
DD
GDD
RRDa/b
TRD1a/b
TRD2a/b
V
CC
3 V/5 V Relay
(polarized or
non-polarized)
相關PDF資料 |
PDF描述 |
|---|---|
| M3AAA-2640K | IDC CABLE - MSC26A/MC26F/MSC26A |
| REC5-4805DRWZ/H6/A | CONV DC/DC 5W 18-72VIN +/-05VOUT |
| SI3216MPPQ1-EVB | BOARD EVAL W/SI3201 INTERFACE |
| VI-JVV-EZ-S | CONVERTER MOD DC/DC 5.8V 25W |
| UUR1V101MNL1GS | CAP ALUM 100UF 35V 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3220PPT-EVB | 制造商:SILABS 制造商全稱:SILABS 功能描述:EVALUATION BOARD FOR THE Si3220 DUAL PROSLIC |
| SI3220PPTX-EVB | 功能描述:音頻 IC 開發工具 Si3220 Eval Board RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| SI3220-X-FQ | 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC |
| SI3220-X-GQ | 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC |
| SI3225 | 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC |
發布緊急采購，3分鐘左右您將得到回復。