- 您現在的位置：買賣IC網 > PDF目錄16215 > SI3225DCX-EVB (Silicon Laboratories Inc)DAUGHTER CARD W/DISCRETE INTRFC PDF資料下載
參數資料
| 型號： | SI3225DCX-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 111/112頁 |
| 文件大?。?/td> | 0K |
| 描述： | DAUGHTER CARD W/DISCRETE INTRFC |
| 標準包裝： | 1 |
| 系列： | ProSLIC® |
| 主要目的： | 接口，模擬前端（AFE） |
| 已用 IC / 零件： | Si3225 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁當前第111頁第112頁
Si3220/25 Si3200/02
98
Rev. 1.3
Not
Recommended
fo
r N
ew
D
esi
gn
s
Figure 64. SLIC Diagnostic Filter Structure
3.32.4. Measurement Tools
8-Bit monitor A/D converter. This 8-bit A/D
converter monitors all dc and low-frequency voltage
and current data from TIP to ground and RING to
ground. Two additional values, TIP – RING and
TIP + RING, are calculated and stored in on-chip
registers to analyze metallic and longitudinal effects.
The A/D operates at an 800 Hz update rate to allow
measurement bandwidth from dc to 400 Hz. A dual-
range capability allows high-voltage/high-current
measurement in the high range but can also
measure lower voltages and currents with a tighter
resolution.
Programmable bandpass filter. A bandpass filter
discriminates certain frequency ranges, such as
ringing frequencies and 50 Hz/60 Hz induction, from
nearby or crossed power leads.
SLIC diagnostics filter. Several post-processing
filter blocks monitor peak dc and ac characteristics of
the Monitor A/D converter outputs and values
derived from these outputs. Setting the SDIAG bit in
the DIAG register enables the filters. There are
separate filters for each channel, and their control is
independent. These filters require DSP processing,
which is available only when voice band processing
is not being performed. If an off-hook or ring trip
condition is detected while the SDIAG bit is set, the
bit is cleared, and the diagnostic information is not
processed.
The following parameters can be selected as inputs
to the diagnostic block by setting the SDIAG bits in
the DIAG register to values 0–7 corresponding to the
order below:
VTIP = voltage on the TIP lead
VRI NG = voltage on the RING lead
VLOOP =VTIP-VRING = metallic (loop) voltage
VLONG =(VTIP+VRING)/2 = longitudinal voltage
ILOOP =ITIP-IRING = metallic (loop) current
ILONG =(ITIP+IRING)/2 = longitudinal current
VRING, EXT = ringing voltage when using an external
ringing source (Si3225 only)
IRING,EXT = ringing current when using an external
ringing source (Si3225 only)
The SLIC diagnostic capability consists of a peak detect
block and two filter blocks, one for dc and one for ac.
The topology is illustrated in Figure 64.
The peak detect filter block reports the magnitude of the
largest positive or negative value without sign. The dc
filter block consists of a single pole IIR low-pass filter
with a coefficient held in the DIAGDCCO RAM location.
The filter output is read from the DIAGDC RAM location.
The ac filter block consists of a full-wave rectifier
followed by a single-pole IIR low-pass filter with a
coefficient held in the DIAGACCO RAM location. The
peak value is read from the DIAGPK RAM location. The
peak value is cleared and the filters are flushed on the
0-1 transition of the SDIAG bit and when the input
source changes. The user can write 0 to the DIAGPK
RAM location to get peak information for a specific time
interval.
16-bit audio A/D converter. The A/D converter
portion of the audio codec is made available for
processing test data received back through the
transmit audio path. The audio path offers a 2.5 V
peak voltage measurement capability and a coarse
attenuation stage for scenarios where the incoming
signal amplitude must be attenuated by as much as
3 dB to bring it into the allowable input range without
clipping.
VTIP
VRING
VLOOP
VLONG
ILOOP
ILONG
VRING,EXT
IRING,EXT
LPF
PEAK
DETECT
FULL WAVE
RECTIFY
LPF
DIAGAC
DIAGDC
DIAGPK
DIAGACCO
DIAGDCCO
相關PDF資料 |
PDF描述 |
|---|---|
| SK102M050ST | CAP ALUM 1000UF 50V 20% RADIAL |
| M3TTK-3036J | IDC CABLE - MSD30K/MC34G/MSD30K |
| SI3225DC0-EVB | DAUGHTER CARD W/SI3200 INTERFACE |
| SEK220M400ST | CAP ALUM 22UF 400V 20% RADIAL |
| CP2201EK | KIT EVAL FOR CP2201 ETH CTRLR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Si3225-FQ | 功能描述:電信線路管理 IC Dual-Channel SLIC/ codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3225-FQR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3225-G-FQ | 功能描述:電信線路管理 IC Dual-Channel SLIC codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3225-G-FQR | 功能描述:電信線路管理 IC Dual-CH SLIC/codec Ext Ringing Support RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Si3225-G-GQ | 功能描述:電信線路管理 IC Dual-Channel SLIC codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。