參數資料
型號： SI3232-G-FQ
廠商： Silicon Laboratories Inc
文件頁數： 60/128頁
文件大小： 0K
描述： IC SLIC PROG DUAL-CH 64TQFP
標準包裝： 160
功能： 用戶線路接口概念（SLIC）
接口： ISDN
電路數： 2
電源電壓： 3.13 V ~ 3.47 V
電流 - 電源： 28mA
功率（瓦特）： 280mW
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 64-TQFP
供應商設備封裝： 64-TQFP（10x10）
包裝： 托盤
Si3232
Preliminary Rev. 0.96
37
Not
Recommended
fo
r N
ew
D
esi
gn
s
4.6. Ringing Generation
The Si3232 is designed to provide a balanced ringing
waveform with or without dc offset. The ringing
frequency, cadence, waveshape, and dc offset are all
register-programmable.
Using a balanced ringing scheme, the ringing signal is
applied to both the TIP and the RING lines using ringing
waveforms that are 180° out of phase with each other.
The resulting ringing signal seen across TIP-RING is
twice the amplitude of the ringing waveform on either
the TIP or the RING line, which allows the ringing
circuitry to withstand only half the total ringing amplitude
seen across TIP-RING.
Figure 16. Balanced Ringing Waveform and
Components
The purpose of an internal ringing scheme is to provide
>40 Vrms into a 5 REN load at the terminal equipment
using a user-provided ringing battery supply. The
specific ringing supply voltage required depends on the
ringing voltage desired.
The ringing amplitude at the terminal equipment
depends on the loop impedance as well as the load
impedance in REN. The following equation can be used
to determine the TIP-RING ringing amplitude required
for a specific load and loop condition.
Figure 17. Simplified Loop Circuit During
Ringing
where
When ringing longer loop lengths, adding a dc offset
voltage is necessary to reliably detect a ring trip
condition (off-hook phone). Adding dc offset to the
ringing signal decreases the maximum possible ringing
amplitude. Adding significant dc offset also increases
the power dissipation in the Si3200 and may require
additional airflow or a modified PCB layout to maintain
acceptable
operating
temperatures.
The
Si3232
automatically applies and removes the ringing signal
during VOC-crossing periods to reduce noise and
crosstalk to adjacent lines. Table 23 provides a list of
registers required for internal ringing generation.
RING
TIP
V
RING
V
TIP
SLIC
V
OFF
GND
V
TIP
V
RING
V
BATH
V
PK
V
OV
V
CM
V
OFF
R
LOOP
V
RING
R
LOAD
V
TERM
+
–
R
OUT
V
TERM
V
RING
R
LOAD
R
LOAD
R
LOOP
R
OUT
++
----------------------------------------------------------------
=
R
LOOP
0.09
per foot for 26 AWG wire
=
R
OUT
320
=
R
LOAD
7000
#REN
--------------------
=
相關PDF資料
PDF描述
VI-2NK-IY-B1 CONVERTER MOD DC/DC 40V 50W
VI-2TK-IY-F1 CONVERTER MOD DC/DC 40V 50W
VI-2TJ-IY-F2 CONVERTER MOD DC/DC 36V 50W
SI3211-E-GM IC PROSLIC/CODEC DTMF 38VQFN
SI3210-GT IC SLIC/CODEC PROG 38TSSOP
相關代理商/技術參數
參數描述
SI3232-G-FQR 功能描述:電信線路管理 IC Dual-CH SLIC only Internal 65 Vrms RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3232-G-GQ 功能描述:電信線路管理 IC Dual-Channel SLIC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3232-G-GQR 功能描述:電信線路管理 IC Dual-CH SLIC only Internal 65 Vrms RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3232-KQ 功能描述:電信線路管理 IC DUAL CH SLIC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3232PPT0-EVB 功能描述:音頻 IC 開發工具 Si3232 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*