- 您現在的位置：買賣IC網 > PDF目錄1967 > SI3452D-B01-GM (Silicon Laboratories Inc)IC POE CONTROLLER MIDSPAN 40QFN PDF資料下載
參數資料
| 型號： | SI3452D-B01-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 6/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POE CONTROLLER MIDSPAN 40QFN |
| 特色產品： | Si3452 Quad High-Voltage Port Controller for PoE and PoE+PSEs |
| 標準包裝： | 50 |
| 控制器類型： | 以太網供電控制器（POE） |
| 接口： | I²C |
| 電源電壓： | 3 V ~ 3.6 V |
| 電流 - 電源： | 14mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN（6x6） |
| 包裝： | 管件 |
| 配用： | SMARTPSE24-KIT-ND - KIT EVAL REF 24PORT SPI/UART |
| 其它名稱： | 336-1835-5 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Si3452
14
Rev. 1.3
4.4. Disconnect Detection
The dV/dt disconnect function can be used to detect a disconnected device without using dc disconnect or ac
disconnect.
In dV/dt disconnect mode, the FET current limit is switched to 7.5 mA. If the voltage across the FET increases, a
load is assumed to be present, and the FET current limit is automatically switched back to its pre-selected value. If,
after 350 ms, the FET voltage has not increased, there is no load present, and the FET is turned off.
In addition to operating in a manner functionally distinct from DC disconnect, dV/dt disconnect requires no
additional external components and fully interoperates with all powered device DC Maintain Power Signatures. For
more information, see “AN399: dV/dt Disconnect and the IEEE 802.3 PoE Standard”.
4.5. Transient Voltage Surge Suppression
The Si3452 features robust on-chip surge protectors on each port; this is an industry first. This unique protection
circuitry acts as an active device that can withstand lightning-induced transients as well as large ESD transient
events. When the port voltage exceeds its protection limit and the current reaches a triggering threshold, current is
shunted from the port to the ground pins.
Internal circuitry is provided to protect the line outputs from externally-coupled fault currents. These are transient
currents of up to 5 A peak.
The operation of the protection circuits depends on the operating mode of the channel switch and the direction of
the fault current. The clamping operation is performed on the detect pin.
The switch itself will also be protected by the current limit. If the transient lasts long enough to heat up the die, then
the temperature sense circuit will shut off the switch, and all the fault current will flow through the clamp diode.
4.6. Temperature Sense
A temperature sense signal is used in conjunction with the current limit status signals from the gate drive blocks.
Any channel that is generating excess heat is assumed to be operating in current limit mode, with both high voltage
drop and high current.
If the port is in PoE mode, an overload will generally not result in thermal shutdown before the 60 ms ICUT period. If
the port is in PoE+ mode, an overload may cause the port to shut down prior to the 60 ms ICUT period. In either
case, the event is reported as ICUT. The faster shutdown in PoE+ mode is consistent with and specifically allowed
by the 802.3at draft and provides much more robust overload protection than is possible with external FETs.
In addition, there is a thermal shutdown if the package temperature exceeds 120 °C. If this threshold is reached, all
output drivers are turned off and detection modes are disabled. This secondary threshold limit guards against the
possibility that the overheating is not caused by a driver operating in current limit.
4.7. Port Measurement and Monitoring
VEE monitoring in conjunction with port current monitoring allows measurement of port power. Port power
monitoring, dynamic power allocation via LLDP*, and port power policing allow efficient power supply sizing.
The Si3452 is factory-calibrated and temperature-compensated for the following measurements:
Port current measurement. These measurements are auto-ranged and scaled to a 16 bit number at 100 A per
bit. Port current accuracy is ±4% ± 2 mA.
VEE is measured with a scale of 64 V. The measurement is reported as a 16-bit number scaled at 1 mV per bit.
VEE measurement accuracy is ±4% over the valid VEE range.
*Note:
LLDP = Link Layer Discovery Protocol. Refer to IEEE 802.3at (draft) and IEEE 802.1AB for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| SI4126-F-BMR | IC SYNTHESIZER RF2/IF 28MLP |
| SI5040-A-GM | IC TXRX XFP 10GBPS 32LGA |
| SI5100-G-BC | IC TXRX SERIAL/DESERIAL 195CBGA |
| SI5110-G-BC | IC TXRX SERIAL/DESERIAL 99BGA |
| SI9200EY | IC PROCESSOR NTWRK SOC 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3452D-B01-GMR | 功能描述:熱插拔功率分布 Quad PoE+ PSE Port Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| SI3452D-B02-GM | 制造商:Silicon Laboratories Inc 功能描述:QUAD HIGH-VOLTAGE PORT CONTROLLER FOR POE AND POE+ PSES 制造商:Silicon Laboratories Inc 功能描述:QUAD POE+ PSE PORT CONTROLLER (AUTO, MIDSPAN, DV/DT DISCONNE - Trays 制造商:Silicon Laboratories Inc 功能描述:IC POE PSE PORT CTLR QUAD 40QFN 制造商:Silicon Laboratories Inc 功能描述:Quad PoE+ PSE Port Controller 制造商:Silicon Laboratories 功能描述:QUAD HIGH-VOLTAGE PORT CONTROLLER FOR POE AND POE+ PSES |
| SI3452D-B02-GMR | 制造商:Silicon Laboratories Inc 功能描述:QUAD POE+ PSE PORT CONTROLLER (AUTO, MIDSPAN, DV/DT DISCONNE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC POE PSE PORT CTLR QUAD 40QFN 制造商:Silicon Laboratories Inc 功能描述:Quad PoE+ PSE Port Controller |
| Si3452MS8-KIT | 功能描述:電源管理IC開發工具 8-Port PoE/PoE+ Midspan PSE Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| SI3453 | 制造商:SILABS 制造商全稱:SILABS 功能描述:QUAD HIGH-VOLTAGE PORT CONTROLLER FOR POE AND POE PSES |
發布緊急采購，3分鐘左右您將得到回復。