- 您現在的位置：買賣IC網 > PDF目錄1970 > ST16C580IQ48-F (Exar Corporation)IC UART FIFO 16B 48TQFP PDF資料下載
參數資料
| 型號： | ST16C580IQ48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 10/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
ST16C580
18
Rev. 1.22
IER BIT-3:
Logic 0 = Disable the modem status register interrupt.
(normal default condition)
Logic 1 = Enable the modem status register interrupt.
IER BIT -4:
Logic 0 = Disable sleep mode. (normal default condi-
tion)
Logic 1 = Enable sleep mode. See Sleep Mode section
for details
IER BIT-5:
Logic 0 = Disable the software flow control, receive
Xoff interrupt. (normal default condition)
Logic 1 = Enable the software flow control, receive
Xoff interrupt. See Software Flow Control section for
details.
IER BIT-6:
Logic 0 = Disable the RTS interrupt. (normal default
condition)
Logic 1 = Enable the RTS interrupt. The 580 issues an
interrupt when the RTS pin transitions from a logic 0
to a logic 1.
IER BIT-7:
Logic 0 = Disable the CTS interrupt. (normal default
condition)
Logic 1 = Enable the CTS interrupt. The 580 issues an
interrupt when CTS pin transitions from a logic 0 to a
logic 1.
FIFO Control Register (FCR)
This register is used to enable the FIFO’s, clear the
FIFO’s, set the transmit/receive FIFO trigger levels,
and select the DMA mode. The DMA, and FIFO
modes are defined as follows:
DMA MODE
Mode 0
Set and enable the interrupt for each
single transmit or receive operation, and is similar to
the ST16C450 mode. Transmit Ready (-TXRDY) will
go to a logic 0 when ever an empty transmit space is
available in the Transmit Holding Register (THR).
Receive Ready (-RXRDY) will go to a logic 0 when-
ever the Receive Holding Register (RHR) is loaded
with a character.
Mode 1
Set and enable the interrupt in a block
mode operation. The transmit interrupt is set when the
transmit FIFO is below the programmed trigger level.
-TXRDY remains a logic 0 as long as one empty FIFO
location is available. The receive interrupt is set when
the receive FIFO fills to the programmed trigger level.
However the FIFO continues to fill regardless of the
programmed level until the FIFO is full. -RXRDY
remains a logic 0 as long as the FIFO fill level is above
the programmed trigger level.
FCR BIT-0:
Logic 0 = Disable the transmit and receive FIFO.
(normal default condition)
Logic 1 = Enable the transmit and receive FIFO. This
bit must be a “1” when other FCR bits are written to or
they will not be programmed.
FCR BIT-1:
Logic 0 = No FIFO receive reset. (normal default
condition)
Logic 1 = Clears the contents of the receive FIFO and
resets the FIFO counter logic (the receive shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-2:
Logic 0 = No FIFO transmit reset. (normal default
condition)
Logic 1 = Clears the contents of the transmit FIFO and
resets the FIFO counter logic (the transmit shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-3:
Logic 0 = Set DMA mode “0”. (normal default condi-
tion)
Logic 1 = Set DMA mode “1.”
Transmit operation in mode “0”:
When the 580 is in the ST16C450 mode (FIFO’s
disabled, FCR bit-0 = logic 0) or in the FIFO mode
(FIFO’s enabled, FCR bit-0 = logic 1, FCR bit-3 = logic
0) and when there are no characters in the transmit FIFO
or transmit holding register, the -TXRDY pin will be a
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650AIJ44-F | IC UART FIFO 32B 44PLCC |
| ST16C654DIQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST78C34CJ44-F | IC UART FIFO 83B 44PLCC |
| ST78C36ACJ44-F | IC UART FIFO 16B 44PLCC |
| SW06GSZ-REEL | IC SWITCH QUAD SPST 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_0508 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。