- 您現在的位置：買賣IC網 > PDF目錄2118 > TAS5711PHP (Texas Instruments)IC AMP AUD DGTL 20W 2CH 48HTQFP PDF資料下載
參數資料
| 型號： | TAS5711PHP |
| 廠商： | Texas Instruments |
| 文件頁數： | 16/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUD DGTL 20W 2CH 48HTQFP |
| 標準包裝： | 250 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲，2.1）或 4 通道（四路） |
| 在某負載時最大輸出功率 x 通道數量： | 21W x 2 @ 8 歐姆 |
| 電源電壓： | 8 V ~ 26 V |
| 特點： | 消除爆音，數字輸入，I²C，I²S，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 48-HTQFP（7x7） |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 包裝： | 托盤 |
| 其它名稱： | 296-32732 TAS5711PHP-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
www.ti.com
SLOS600A – DECEMBER 2009 – REVISED AUGUST 2010
DETAILED DESCRIPTION
POWER SUPPLY
To facilitate system design, the TAS5711 needs only a 3.3-V supply in addition to the (typical) 18-V power-stage
supply. An internal voltage regulator provides suitable voltage levels for the gate drive circuitry. Additionally, all
circuitry requiring a floating voltage supply, e.g., the high-side gate drive, is accommodated by built-in bootstrap
circuitry requiring only a few external capacitors.
In order to provide good electrical and acoustical characteristics, the PWM signal path for the output stage is
designed as identical, independent half-bridges. For this reason, each half-bridge has separate bootstrap pins
(BST_x), and power-stage supply pins (PVDD_x). The gate drive voltages (GVDD_AB and GVDD_CD) are
derived from the PVDD voltage. Special attention should be paid to placing all decoupling capacitors as close to
their associated pins as possible. In general, inductance between the power-supply pins and decoupling
capacitors must be avoided.
For a properly functioning bootstrap circuit, a small ceramic capacitor must be connected from each bootstrap pin
(BST_x) to the power-stage output pin (OUT_x). When the power-stage output is low, the bootstrap capacitor is
charged through an internal diode connected between the gate-drive regulator output pin (GVDD_x) and the
bootstrap pin. When the power-stage output is high, the bootstrap capacitor potential is shifted above the output
potential and thus provides a suitable voltage supply for the high-side gate driver. In an application with PWM
switching frequencies in the range from 352 kHz to 384 kHz, it is recommended to use 33-nF 50-V X7R
capacitors, size 0603 or 0805, for the bootstrap supply. These 33-nF capacitors ensure sufficient energy storage,
even during minimal PWM duty cycles, to keep the high-side power stage FET (LDMOS) fully turned on during
the remaining part of the PWM cycle.
Special attention should be paid to the power-stage power supply; this includes component selection, PCB
placement, and routing. As indicated, each half-bridge has independent power-stage supply pins (PVDD_x). For
optimal electrical performance, EMC compliance, and system reliability, it is important that each PVDD_x pin is
decoupled with a 100-nF ceramic capacitor placed as close as possible to each supply pin.
The TAS5711 is fully protected against erroneous power-stage turnon due to parasitic gate charging.
ERROR REPORTING
The A_SEL pin has two functions: I2C device-address select and fault indication. On RESET, this pin is an input
and defines the I2C address. But this pin can be programmed after RESET to be an output by writing 1 to bit 0 of
Any fault resulting in device shutdown is signaled by the A_SEL pin going low (see Table 1). A latched version of
this pin is available on D1 of register 0x02. The bit can be cleared only by an I2C write.
Table 1. FAULT Output States
FAULT
DESCRIPTION
0
Overcurrent (OC) or undervoltage (UVP) error or overtemperature error (OTE) or over
voltage ERROR
1
No faults (normal operation)
Copyright 2009–2010, Texas Instruments Incorporated
23
Product Folder Link(s): TAS5711
相關PDF資料 |
PDF描述 |
|---|---|
| TC1025CEPA | IC COMPARATOR 1.8V DUAL 8DIP |
| TC1027CEOR | IC COMPARATOR 1.8V QUAD 16SOIC |
| TC3400VOA | IC ADC 16BIT 1.8V LOW PWR 8-SOIC |
| TC3401VPE | IC ADC 16BIT 1.8V DUAL LP 16DIP |
| TC3402VQRTR | IC ADC 16BIT 1.8V QUAD LP 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5711PHP | 制造商:Texas Instruments 功能描述:Audio Power Amplifier IC 制造商:Texas Instruments 功能描述:IC, AUDIO PWR AMP, CLASS D, 20W HTQFP-48 |
| TAS5711PHPEVM | 功能描述:音頻 IC 開發工具 TAS5711PHP Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TAS5711PHPR | 功能描述:音頻放大器 2-Channel Dig Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5713 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:25-W DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
| TAS5713_10 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:25-W DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
發布緊急采購，3分鐘左右您將得到回復。