- 您現在的位置：買賣IC網 > PDF目錄371182 > TDA8580J (NXP Semiconductors N.V.) Multi-purpose power amplifier PDF資料下載
參數資料
| 型號： | TDA8580J |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Multi-purpose power amplifier |
| 中文描述： | 多用途功率放大器 |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 181K |
| 代理商： | TDA8580J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2000 Apr 18
16
Philips Semiconductors
Preliminary specification
Multi-purpose power amplifier
TDA8580J
APPLICATION INFORMATION
The application circuit depends on the supply voltage
used. For supply voltages below 18 V the application
circuits are shown in Figs 28, 29 and 30.
The typical application circuits for the different supply
voltage ranges are shown in Figs 31, 32 and 33.
Additional information for the applications shown in
Figs 28, 29 and 30
The RC-network connected to pin 5 determines the
amplifier switch on/off behaviour as follows;
Switched from STANDBY to MUTE when V
switching
(typically 9 V) is enabled and the switch SW1 is closed.
During MUTE there is no output noise and no offset.
Switched from MUTE to ON when the switch SW1 is
opened. During switching ON the offset and noise are
gradually built up. The time constant is fixed by R1
×
C1.
Theinputscanbetiedtogetherandconnectedtooneinput
capacitor. Because the input resistance is decreased by a
factor of 2, the low frequency roll-off is shifted to a higher
frequency when C
i
is kept the same value.
The low frequency cut-off is determined by;
The Boucherot network connected to the buffer (pin 9) is
necessary to guarantee a low output resistance at high
frequencies when the buffer is loaded (only in SE
applications).
Additional information for the applications shown in
Figs 31, 32 and 33
Short circuit behaviour at high supply voltages (V
p
> 18 V):
When V
p
> 18 V it is advisable to use the applications
given in Figs 32 and 33. In these applications the
diagnostics output is tied to pin 5 (one pin operation) or
pin 13 (two pin operation). During a fault condition the
amplifier is soft-muted and the amplitude of the output
signal is reduced at:
– over temperature (still large dynamic range)
– short to ground and over load (output current
reduced)
The 4.7
μ
F capacitor and the 10 k
resistor connected
to pin 5 or to pin 13 are used to:
– provide a stable loop
– control the switch on/off behaviour
– minimize the effect due to clip detection.
Use of common buffer
In SE applications the buffer output is used in place of a
SE capacitor. To minimize the crosstalk (high channel
separation) and distortion it is advised to connect the
speaker wires as closely as possible to pin 9 without using
a shared wire. Internally in the IC all the efforts have been
taken to minimize the crosstalk by locating the feedback
loops as close as possible to pin 9.
If a common wire is shared by all the speakers, the series
resistance of this shared wire will introduce added signal
voltages resulting from the currents flowing through this
wire when a connected amplifier is driven by a signal.
Optimize the THD performance
The TDA8580J application can be optimized to gain the
lowest THD possible by applying the following guidelines:
SE application: minimize the shared wires to pin 9 (see
section “Use of common buffer”).
Because the inputs are quasi differential, ground loops
can be avoided by connecting the negative terminal of
the 100
μ
F signal ground capacitor (connected to
pin 12) to the ground pin of the signal processor.
Note: do not leave the inputs in the open condition to
prevent HF oscillation.
Increase the value of electrolytic supply capacitor
(typical value 1000
μ
F) to the maximum possible to
minimize cross talk and distortion at low signal
frequencies, due to the PSRR (power supply rejection
ratio). For suppressing high frequency transients on the
supply line a capacitor (typical value 100 nF) with a low
ESR is required to be connected in parallel with the
electrolytic capacitor. The capacitor combination must
be placed as close as possible to the IC (using short
interconnection tracks).
Headroom
A typical CD requires at least 12 dB dynamic headroom
(a factor of 15.85), compared with the average power
output, for passing the loudest parts without distortion.
f
3dB
–
1
2
π
(
R
i
C
i
)
×
×
2
π
60
10
3
×
220
10
9
–
×
×
×
--------------------------------1
12 Hz.
=
=
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8591J | 4 X 44 W into 4 or 4 X 75 W into 2 quad BTL car radio power amplifier |
| TDA8601 | RGB/YUV and fast blanking switch |
| TDA8601T | RGB/YUV and fast blanking switch |
| TDA8741 | satellite sound circuit with noise reduction |
| TDA8741H | Satellite sound circuit with noise reduction |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8581 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multi-purpose high-gain power amplifier |
| TDA8586 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Power amplifier with load detection and auto BTL/SE selection |
| TDA8586Q | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Power amplifier with load detection and auto BTL/SE selection |
| TDA8586TH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Power amplifier with load detection and auto BTL/SE selection |
| TDA8588AJ | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled 4 x 50 Watt power amplifier and multiple voltage regulator |
發布緊急采購，3分鐘左右您將得到回復。