- 您現在的位置：買賣IC網 > PDF目錄98218 > THS1031IPWLE (TEXAS INSTRUMENTS INC) 10-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF資料下載
參數資料
| 型號： | THS1031IPWLE |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 10-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | PLASTIC, TSSOP-28 |
| 文件頁數： | 4/22頁 |
| 文件大?。?/td> | 296K |
| 代理商： | THS1031IPWLE |
THS1031
COMPLETE SOLUTION 2.7 V ~ 5.5 V, 10-BIT, 30 MSPS
CMOS ANALOG-TO-DIGITAL CONVERTER
SLAS242 – NOVEMBER 1999
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
reference operations (continued)
ADC reference
The MODE pin is used to select the reference source for the ADC.
D Internal ADC Reference: Connect the MODE pin to AVDD to use the reference source for ADC generated
on the VREF pin. (See VREF REFERENCE described in Table 2) such that (REFTF–REFBF) = VREF and
(REFTF+REFBF)/2 is set to a voltage for optimum operation of the ADC (near AVDD/2).
D External ADC Reference: To supply an external reference source to the ADC, connect the MODE pin to
AGND. An external reference source should be connected to REFTF/REFTS and REFBF/REFBS.
MODE = AGND closes internal switches to allow a Kelvin connection through REFTS/REFBS, and disables
the on-chip amplifiers which drive on to the ADC references. Differential input is not supported
analog input mode
single-ended input
The single-ended input can be configured to work with either an external ADC reference or internal ADC
reference.
D External ADC Reference Mode: A single-ended analog input is accepted at the AIN pin where the input
signal is bounded by the voltages on the REFTS and REFBS pins. Figure 7 shows an example of applying
external reference to REFTS and REFBS pins in which REFTS is connected to the low-impedance 2-V
source and REFBS is connected to the low-impedance 2-V source. REFTS and REFBS may be driven to
any voltage within the supply as long as the difference (REFTS – REFBS) is between 1 V and 2 V as
specified in Table 2. Figure 8 shows an example of external-reference using a Kelvin connection to eliminate
line voltage drop errors.
SHA
A/D
PGA
SW3
REFBF
REFTF
MODE
REFBS
REFTS
10
F
0.1
F
0.1
F
0.1
F
2 V
1 V
AIN
2 V
1 V
THS1031
Figure 7. External ADC Reference Mode
PRODUCT
PREVIEW
相關PDF資料 |
PDF描述 |
|---|---|
| THS1031CPWLE | 10-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1040CDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1040IPW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1040CPWR | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1040IPWRG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1031IPWR | 功能描述:模數轉換器 - ADC 10-Bit 30 MSPS 1-Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1031IPWRG4 | 功能描述:模數轉換器 - ADC 10-Bit 30 MSPS 1-Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1031SOIC | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER |
| THS1031TSSOP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER |
| THS10330RJ | 功能描述:線繞電阻器 - 底架安裝 THS10 330R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
發布緊急采購，3分鐘左右您將得到回復。