- 您現在的位置：買賣IC網 > PDF目錄385925 > THS4500EVM (Texas Instruments, Inc.) THS4500 Evalutation Module(THS4500評估板) PDF資料下載
參數資料
| 型號： | THS4500EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | THS4500 Evalutation Module(THS4500評估板) |
| 中文描述： | THS4500 Evalutation模塊（THS4500評估板） |
| 文件頁數： | 14/25頁 |
| 文件大?。?/td> | 313K |
| 代理商： | THS4500EVM |
Required Equipment
2-2
2.1
Required Equipment
One dual-output dc power supply (
±
5 V, 1 A output minimum)
One single-output dc power supply (5 V, 1 A output minimum). This power
supply is used to activate the power-down function of the EVM, and will
be referred to in the text of this document as the
power-down supply.
Two dc current meters with resolution to 1 mA and capable of the
maximum current the dc power supply can supply.
50-
source impedance function generator (1 MHz, 10 V
PP
sine wave)
Oscilloscope (50-MHz bandwidth minimum, 50-
input impedance)
Three BNC-to-SMA cables
BNC-to-BNC cable
Seven banana-to-banana wires; 5 red, 2 black
Banana to test clip wire
2.2 Power Supply Connection
(See Figure 2
–
1)
1)
Set the dual dc power supply to
±
5 V. If available, set the current limit on
the dc power supply to 100 mA.
2)
Make sure the dual dc power supply is turned off before proceeding to the
next step.
3)
Connect the positive (+) terminal of the power supply to the positive (+)
terminal of the current meter number 1.
4)
Connect the negative (
–
) terminal of the current meter number 1 to +VS
(J8).
5)
Connect the common ground terminal of the power supply to GND (J7).
6)
Connect the negative (
–
) terminal of the power supply to the negative (
–
)
terminal of the second current meter.
7)
Connect the positive (+) terminal of the current meter number 2 to
–
VS
(J5).
8)
Set the power-down supply to
–
5 Vdc, turn it off.
9)
Connect the negative (
–
) terminal of the power-down supply to GND (J7).
10) Connect the positive (+) terminal of the power-down supply to Power
Down (TP2).
相關PDF資料 |
PDF描述 |
|---|---|
| THS5661ADW | 12-BIT, 125 MSPS, CommsDACE DIGITAL-TO-ANALOG CONVERTER |
| THS5661APW | 12-BIT, 125 MSPS, CommsDACE DIGITAL-TO-ANALOG CONVERTER |
| THS5671ADW | 14-BIT, 125 MSPS, CommsDAC DIGITAL-TO-ANALOG CONVERTER |
| THS5671APW | 14-BIT, 125 MSPS, CommsDAC DIGITAL-TO-ANALOG CONVERTER |
| THS5671AIDWR | 14-BIT, 125 MSPS, CommsDAC DIGITAL-TO-ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4500ID | 功能描述:特殊用途放大器 High-Speed Fully Differential +/-5 V RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| THS4500IDG4 | 功能描述:特殊用途放大器 High-Speed Fully Differential +/-5 V RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| THS4500IDGK | 功能描述:特殊用途放大器 High-Speed Fully Differential +/-5 V RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| THS4500IDGKG4 | 功能描述:特殊用途放大器 High-Speed Fully Differential +/-5 V RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| THS4500IDGKR | 功能描述:特殊用途放大器 High-Speed Fully Differential +/-5 V RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。