- 您現在的位置：買賣IC網 > PDF目錄373643 > TJA1053T (NXP SEMICONDUCTORS) Fault-tolerant CAN transceiver PDF資料下載
參數資料
| 型號： | TJA1053T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | Fault-tolerant CAN transceiver |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PDSO14 |
| 封裝： | PLASTIC, SO-14 |
| 文件頁數： | 15/20頁 |
| 文件大?。?/td> | 113K |
| 代理商： | TJA1053T |
1997 Oct 15
15
Philips Semiconductors
Preliminary specification
Fault-tolerant CAN transceiver
TJA1053
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TJM4558 | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TJM4558C | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TJM4558I | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TK15H50C | Field Effect Transistor Silicon N-Channel MOS Type (ヰ-MOS VI) |
| TK19H50C | TOSHIBA Field Effect Transistor Silicon N-Channel MOS Type (MOS VI) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TJA1053T/N,112 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053T/N,118 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053T/N1,512 | 功能描述:IC CAN TXRX FAULT-TOL 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| TJA1053T/N1,518 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053TD | 功能描述:網絡控制器與處理器 IC CAN XCVR FAULT-TOL RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。