- 您現在的位置：買賣IC網 > PDF目錄373643 > TJA1053T (NXP SEMICONDUCTORS) Fault-tolerant CAN transceiver PDF資料下載
參數資料
| 型號： | TJA1053T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | Fault-tolerant CAN transceiver |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PDSO14 |
| 封裝： | PLASTIC, SO-14 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 113K |
| 代理商： | TJA1053T |
1997 Oct 15
5
Philips Semiconductors
Preliminary specification
Fault-tolerant CAN transceiver
TJA1053
FUNCTIONAL DESCRIPTION
The TJA1053 is the interface between the CAN protocol
controller and the physical bus. It is primarily intended for
low speed applications, up to 125 kBaud, in passenger
cars. The device provides differential transmit capability to
the bus and differential receive capability to the CAN
controller.
To reduce RF interference the rise and fall slope are
limited. This allows the use of an unshielded twisted pair or
a parallel pair of wires for the bus. Moreover, it supports
transmission capability on either bus wire if one of the bus
wires is corrupted. The failure detection logic automatically
selects a suitable transmission mode.
In normal operation (no wiring failures) the differential
receiver is output to RXD. The differential receiver inputs
are connected to CANH and CANL through integrated
filters. The filtered input signals are also used for the single
wire receivers. The CANH and CANL receivers have
threshold voltages that ensure a maximum noise margin in
single-wire modes.
A timer has been integrated at the TXD input. This timer
prevents the TJA1053 to drive the bus lines to permanent
dominant state.
Failure detector
The failure detector is active in the normal operation mode
and detects the following single bus failures and switches
to an appropriate mode:
1.
CANH wire interrupted
2.
CANL wire interrupted
3.
CANH short-circuited to battery
4.
CANL short-circuited to ground
5.
CANH short-circuited to ground
6.
CANL short-circuited to battery
7.
CANL mutually shorted to CANH.
The differential receiver threshold is set at
2.9 V.
This ensures correct reception in the normal operating
modes and, in the event of failures 1, 2 and 5 with a noise
margin as high as possible. These failures, or recovery
from them, do not destroy ongoing transmissions.
Failures 3 and 6 are detected by comparators connected
to CANH and CANL, respectively. If the comparator
threshold is exceeded for a certain period of time, the
reception is switched to the single-wire mode.
This time is needed to avoid false triggering by external RF
fields. Recovery from these failures is detected
automatically after a certain time-out (filtering) and no
transmission is lost. The CANH driver and the RTH pin are
switched off in the event of failure 3.
Failures 4 and 7 initially result in a permanent dominant
level at RXD. After a time-out, the CANL driver and the
RTL pin are switched off. Only a weak pull-up at RTL
remains. Reception continues by switching to the
single-wire mode via CANH. When failures 4 or 7 are
removed, the recessive bus levels are restored. If the
differential voltage remains below the recessive threshold
level for a certain period of time, reception and
transmission switch back to the differential mode.
If any of the seven wiring failures occur, the output NERR
will be made LOW. On error recovery, NERR will be made
HIGH again.
During all single-wire transmissions, the EMC
performance (both immunity and emission) is worse than
in the differential mode. Integrated receiver filters
suppress any HF noise induced into the bus wires.
The cut-off frequency of these filters is a compromise
between propagation delay and HF suppression. In the
single-wire mode, low frequency noise cannot be
distinguished from the required signal.
Low power modes
The transceiver provides 3 low power modes which can be
entered and exited via pins STB and EN (see Table 1).
The sleep mode is the mode with the lowest power
consumption. The INH pin is switched to high-impedance
for deactivation of external voltage regulators. CANL is
biased to the battery voltage via the RTL output. If the
supply voltage is provided the RXD and NERR will signal
the wake-up interrupt
The V
BAT
standby mode will react the same as the sleep
mode with an active INH output.
The V
CC
standby mode is the V
BAT
standby with RTL
switched to the V
CC
voltage. In this mode the NERR output
signals the V
BAT
power-on flag and the RXD output will
show the wake-up interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| TJM4558 | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TJM4558C | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TJM4558I | WIDE BANDWIDTH DUAL BIPOLAR OPERATIONAL AMPLIFIERS |
| TK15H50C | Field Effect Transistor Silicon N-Channel MOS Type (ヰ-MOS VI) |
| TK19H50C | TOSHIBA Field Effect Transistor Silicon N-Channel MOS Type (MOS VI) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TJA1053T/N,112 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053T/N,118 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053T/N1,512 | 功能描述:IC CAN TXRX FAULT-TOL 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| TJA1053T/N1,518 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1053TD | 功能描述:網絡控制器與處理器 IC CAN XCVR FAULT-TOL RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。