- 您現在的位置：買賣IC網 > PDF目錄383953 > TLC32044MFK (Texas Instruments, Inc.) VOICE-BAND ANALOG INTERFACE CIRCUITS PDF資料下載
參數資料
| 型號： | TLC32044MFK |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| 中文描述： | 語音頻帶模擬接口電路 |
| 文件頁數： | 12/39頁 |
| 文件大小： | 535K |
| 代理商： | TLC32044MFK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
TLC32044C, TLC32044E, TLC32044I, TLC32044M TLC32045C, TLC32045I
VOICE-BAND ANALOG INTERFACE CIRCUITS
SLAS017F – MARCH 1988 – REVISED MAY 1995
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
secondary DX serial communication protocol
x x |
←
to TA register
→
| x x |
←
to RA register
→
|
x |
←
to TA’ register
→
| x |
←
to RA’ register
→
|
x |
←
to TB register
→
| x |
←
to RB register
→
|
x x x x x x d9
0
0
d13 and d6 are MSBs (unsigned binary)
0
1
d14 and d7 are 2’s complement sign bits
1
0
d14 and d7 are MSBs (unsigned binary)
x d7 d6 d5 d4 d3 d2
1
1
Control
Register
d2 = 0/1 deletes/inserts the A/D high-pass filter
d3 = 0/1 disables/enables the loopback function
d4 = 0/1 disables/enables the AUX IN+ and AUX IN–
d5 = 0/1 asynchronous/synchronous transmit and receive sections
d6 = 0/1 gain control bits (see gain control section)
d7 = 0/1 gain control bits (see gain control section)
d9 = 0/1 delete/insert on-board second-order (sin x)/x correction filter
reset function
A reset function is provided to initiate serial communications between the AIC and DSP. The reset function
initializes all AIC registers, including the control register. After power has been applied to the AIC, a
negative-going pulse on RESET initializes the AIC registers to provide an 8-kHz A/D and D/A conversion rate
for a 5.184 MHz master clock input signal. The AIC, except the control register, is initialized as follows (see AIC
DX data word format section):
REGISTER
INITIALIZED
REGISTER
VALUE (HEX)
TA
9
TA’
1
TB
24
RA
9
RA’
1
RB
24
The control register bits are reset as follows (see AIC DX data word format section):
d9 = 1, d7 = 1, d6 = 1, d5 = 1, d4 = 0, d3 = 0, d2 = 1
This initialization allows normal serial port communications to occur between AIC and DSP. If the transmit and
receive sections are configured to operate synchronously and the user wishes to program different conversion
rates, only the TA, TA’, and TB register need to be programmed, since both transmit and receive timing are
synchronously derived from these registers (see the terminal functions table and AIC DX word format sections).
The circuit shown in Figure 1 provides a reset on power up when power is applied in the sequence given under
power-up sequence. The circuit depends on the power supplies reaching their recommended values a minimum
of 800 ns before the capacitor charges to 0.8 V above DGTL GND.
VCC+
VCC–
RESET
200 k
0.5
μ
F
TLC32044/TLC32045
5 V
–5 V
Figure 1. Power-Up Reset
相關PDF資料 |
PDF描述 |
|---|---|
| TLC32045C | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32045I | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32046C | Wide-Band Analog Interface Circuit |
| TLC32046I | Wide-Band Analog Interface Circuit |
| TLC32046M | Wide-Band Analog Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC32044MFK/B | 制造商:Rochester Electronics LLC 功能描述: |
| TLC32044MFKB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| TLC32044MJ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32044MJB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| TLC32045C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND ANALOG INTERFACE CIRCUITS |
發布緊急采購，3分鐘左右您將得到回復。