- 您現在的位置：買賣IC網 > PDF目錄98243 > TLC5618CP (TEXAS INSTRUMENTS INC) SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, PDIP8 PDF資料下載
參數資料
| 型號： | TLC5618CP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | DAC |
| 英文描述： | SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 8/26頁 |
| 文件大?。?/td> | 386K |
| 代理商： | TLC5618CP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
TLC5618, TLC5618A
PROGRAMMABLE DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTERS
SLAS156G – JULY 1997 – REVISED APRIL 2001
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
changing the latch B data from zero to full code
Assuming that latch B starts at zero code (e.g., after power-up), the latch can be filled with 1s by writing (bit D15
on the left, D0 on the right).
0X00 1111 1111 1111
to the serial interface. Bit D14 can be zero to select slow mode or one to select fast mode. The data (bits D0
to D11) are written to both the double buffer and latch B.
The latch A contents and the DAC A output are not changed by this write.
double-buffered change of both DAC outputs
Assuming that DACs A and B start at zero code (e.g., after power-up), if DAC A is to be driven to mid-scale and
DAC B to full-scale, and if the outputs are to begin rising at the same time, this can be achieved as follows:
First,
0d01 1111 1111 1111
is written (bit D15 on the left, D0 on the right) to the serial interface. This loads the full-scale code into the double
buffer but does not change the latch B contents and the DAC B output voltage. The latch A contents and the
DAC A output are also unaffected by this write operation.
Changing from fast to slow or slow to fast mode changes the supply current which can glitch the outputs, and
so D14 (designated by d in the above data word) should be set to maintain the speed mode set by the previous
write.
Next,
1X0X 1000 0000 0000
is written (bit D15 on the left, D0 on the right) to the serial interface. Bit D14 can be zero to select slow mode
or one to select fast mode. The other X can be zero or one (don’t care). This writes the mid-scale code
(100000000000) to latch A and also copies the full-scale code from the double buffer to latch B. Both DAC
outputs thus begin to rise after the second write.
DSP serial interface
Utilizing a simple 3-wire serial interface shown in Figure 22, the TLC5618A can be interfaced to TMS320
compatible serial ports. The 5618A has an internal state machine that will count 16 clocks after receiving a falling
edge of CS and then disable further clocking in of data until the next falling edge is received on CS. Therefore
CS can be connected directly to the FS pins of the serial port and only the leading falling edge of the DSP will
be used to start the write process. The TLC5618A is designed to be used with the TMS320Cxx DSP in burst
mode serial port transmit operation.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC5618AMFK | SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, CQCC20 |
| TLC5618IP | SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, PDIP8 |
| TLC5620CN | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDIP14 |
| TLC5620CDR | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
| TLC5620IDR | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC5618ID | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TLC5618IDR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTERS |
| TLC5618IP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTERS |
| TLC5620 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUADRUPLE 8-BIT DIGITAL-TO-ANALOG CONVERTERS |
| TLC5620C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUADRUPLE 8-BIT DIGITAL-TO-ANALOG CONVERTERS |
發布緊急采購，3分鐘左右您將得到回復。