- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS51315RGFT (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC40 PDF資料下載
參數資料
| 型號： | TPS51315RGFT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | GREEN, PLASTIC, QFN-40 |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 1028K |
| 代理商： | TPS51315RGFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
OUT
V
0.75
R1
R2
0.75
-
=
(
)
(
)
f
OUT
ON max
IN min
V
1
T
V
=
( )
(
)
(
)
(
)
( )
IN min
ON(max)
T on
12
OUT
V
T
50ns
3
R
2
V
150mV
19 10
-
=
W
+
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
f
OUT
IN max
IND
IND ripple f
IN max
OUT max
IN max
V
1
3
L
I
V
I
V
-
-
=
=
(
)
( )
(
)
(
)
(
)
f
OUT
IN max
TRIP
IND peak
DS on
IN max
V
1
I
R
2 L
V
-
=
+
(
)
(
)
OUT
RIPPLE
OUT max
V
0.015
V
ESR
60 m
I
0.75
I
=
W
SLUS881A
– MAY 2009 – REVISED MAY 2011
External Component Selection
External component selection is a simple process in D-CAP
Mode.
1. Determine the value of R1 and R2.
The recommended R2 value is 10 k
to 100 k. Calculate R1 by using Equation 8.
(8)
2. Choose RT(on)
The switching frequency is usually determined by overall view of the dc-dc converter designer in
consideration of size, efficiency or cost, and mostly dictated by external component constraints such as the
size of inductor and/or the output capacitor. If an extremely low or high duty factor is expected, the minimum
on-time or off-time must also be considered to satisfy the required duty factor. Once the switching frequency
(9)
(10)
3. Choose the inductor.
To begin, choose an inductance value where the ripple current is approximately 1/4 to 1/2 of the maximum
output current.
(11)
For applications that require a fast transient response with a minimum of VOUT overshoot, consider a smaller
inductance value than calculated in Equation 11. The cost of a small inductance value is higher steady-state
ripple, larger line regulation, and higher switching loss.
The inductor also needs to have low DCR to achieve good efficiency, as well as enough room above the
peak inductor current before saturation. The peak inductor current can be estimated by Equation 12.
(12)
4. Choose output capacitor(s).
Organic semiconductor capacitor(s) or specialty polymer capacitor(s) are recommended. Determine an ESR
to meet the required ripple voltage. A quick approximation is shown in Equation 13.
(13)
Copyright
2009–2011, Texas Instruments Incorporated
19
相關PDF資料 |
PDF描述 |
|---|---|
| TPS51317RGBT | SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS51317RGBR | SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS51427ARHBR | DUAL SWITCHING CONTROLLER, PQCC32 |
| TPS51427ARHBT | DUAL SWITCHING CONTROLLER, PQCC32 |
| TPS51461RGET | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS51317 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3-V/5-V Input, 6-A, D-CAP+? Mode Synchronous Step-Down Integrated FETs Converter |
| TPS51317RGBR | 功能描述:直流/直流開關轉換器 3.3V/5Vin,6A,DCAP Mode Sync Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS51317RGBT | 功能描述:直流/直流開關轉換器 3.3V/5Vin,6A,DCAP Mode Sync Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS51362RVER | 制造商:Texas Instruments 功能描述:22V INPUT, 10A INTEGRATED FET 制造商:Texas Instruments 功能描述:IC REG BUCK SYNC ADJ 10A 28VQFN |
| TPS51362RVET | 制造商:Texas Instruments 功能描述:22V INPUT, 10A INTEGRATED FET 制造商:Texas Instruments 功能描述:IC REG BUCK SYNC ADJ 10A 28VQFN |
發布緊急采購，3分鐘左右您將得到回復。