- 您現在的位置：買賣IC網 > PDF目錄373685 > TQ6122 (TriQuint Semiconductor,Inc.) 1 Gigasample/sec, 8-bit Digital-to-Analog Converter PDF資料下載
參數資料
| 型號： | TQ6122 |
| 廠商： | TriQuint Semiconductor,Inc. |
| 英文描述： | 1 Gigasample/sec, 8-bit Digital-to-Analog Converter |
| 中文描述： | 1 Gigasample /秒，8位數字到模擬轉換器 |
| 文件頁數： | 10/23頁 |
| 文件大?。?/td> | 939K |
| 代理商： | TQ6122 |
TQ6122
10
For additional information and latest specifications, see our website:
www.triquint.com
Circuit Description
The TQ6122 DAC is based on a current-steering archi-
tecture in which weighted currents are switched by an
array of differential-pair switches into either the V
OUT
or V
OUT
output, depending on the state of the input data
and blanking bits. Essentially, the DAC is comprised
of
six circuit blocks: the input buffer, the data multiplexer,
blanking logic, master/slave latch array with segment
encode logic, differential-pair switches, and the current
source array. (See figure on page 1.)
Input Buffers
The input buffers compare the ECL data and control
input signals with the ECLREF level, amplify the differ-
ence, and translate this signal to the logic levels used
within the IC. By default, the ECL reference is set by an
internal generator; however, for best performance and
maximum noise margin over temperature, power supply,
and device-to-device variations, the user should
provide
an external level. For general-purpose applications, a
simple resistive divider between D
GND
and V
TT
will
suffice. For extreme environments or for maximum
performance, the ECLREF level should be slaved to the
centerpoint of the incoming data. Refer to the “Digital
Inputs and Terminations” discussion later in this
document for additional information.
Note that the data inputs are complemented to indicate
that an increasing input value results in the V
OUT
level
moving more negative.
Data Multiplexer
The DAC makes provision for accepting data from
either of two sources: from a single 8-bit-wide word at
the full conversion rate, or from two 8-bit-wide half-
speed words which are multiplexed together inside the
DAC under the control of the SELA input. In use, the
SELA input is set HIGH to select the A-Word data and
LOW to select the B-Word. It is generally best to use
the A-Word input when operating the DAC unmultiplexed,
although the B-Word supports full-rate transfers.
Blanking Logic
A separate BLANK input is included to allow the DAC to
be used in video display applications. When asserted
LOW, the BLANK input has no effect on the operation of
the DAC, and the state of the input data words controls
the positions of the current switches. When BLANK is
asserted HIGH, however, all internal data bits and the
internal blanking bit are synchronously forced HIGH at
the next negative-going clock transition, causing the
V
OUT
output to go to its most negative level. This level
is the sum of the normal level associated with an input
code of 11111111 plus the increment due to the
blanking current being steered away from the V
OUT
output to V
OUT
. See Figure 4 (B).
In order to provide more latitude in the timing of the
BLANK signal, the BLANK input is sampled only when
the A-Word is selected. When the B-Word is selected,
the state of the BLANK input at the time the SELA
control line goes LOW is held stable until SELA again
goes HIGH. In situations where blanking is not used,
it is important that the BLANK input be tied to a solid
logic LOW to prevent accidental assertion of BLANK =
HIGH. Note also that when the DAC is used in the
unmultiplexed mode, the data should be brought in on
the A-Word inputs, since with SELA = LOW (as would
be the case for B-Word operation), a transient HIGH
level at the BLANK input would never be cleared and
the DAC would lock up.
The BLANK_DISABLE pin is normally tied to the V
AA
rail, allowing I
BLANK
to flow to the differential-pair
switch and then to the selected output. For applications
which do not use blanking, however, the standing
offset in the V
OUT
output due to the unswitched
相關PDF資料 |
PDF描述 |
|---|---|
| TQ6124 | 1 Gigasample/sec, 14-bit Digital-to-Analog Convertor |
| TQ7125 | 3V HBT TDMA Power Amplifier IC |
| TQ7625 | 3V HBT TDMA Power Amplifier IC |
| TQ8015 | 1.25 Gigabit/sec 16x16 Digital ECL Crosspoint Switch |
| TQ8016 | 1.3 Gigabit/sec 16x16 Digital ECL Crosspoint Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TQ6122-M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter |
| TQ6124 | 制造商:TRIQUINT 制造商全稱:TriQuint Semiconductor 功能描述:1 Gigasample/sec, 14-bit Digital-to-Analog Convertor |
| TQ6124-CM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:14-Bit Digital-to-Analog Converter |
| TQ651C2 | 制造商:Honeywell Sensing and Control 功能描述:GAUGE, TORQUE WATCH 10N-MM TO 140N-MM 2%; Torque Range N-m:10N-mm to 140N-mm; Torque Range ft-lb:0.005lb-ft to 0.104lb-ft; Accuracy %:2%; Accuracy:+/-2%; Torque Max:20in-oz; Torque Min:1in-oz ;RoHS Compliant: NA |
| TQ651C3 | 制造商:Honeywell Sensing and Control 功能描述:GAUGE, TORQUE WATCH 15N-MM TO 285N-MM 2%; Torque Range N-m:15N-mm to 265N-mm; Torque Range ft-lb:0.01lb-ft to 0.208lb-ft; Accuracy %:2%; Accuracy:+/-2%; Torque Max:40in-oz; Torque Min:2in-oz ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。