參數資料
型號: TSC2111IRGZTG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC48
封裝: PLASTIC, QFN-48
文件頁數: 41/99頁
文件大小: 1143K
代理商: TSC2111IRGZTG4
TSC2111
SLAS495A JUNE 2006 REVISED OCTOBER 2007
www.ti.com
46
Where:
VREF is the SAR ADC reference
Vsar is input to the SAR ADC
The TSC2111 supports programmable autoauxiliary measurement mode, which can be enabled using control
register 0CH/page 1. In this mode, the TSC2111 can auto start the auxiliary measurement after a programmable
interval. The user can program minimum and maximum threshold values through a register. If the measurement
goes outside the threshold range, the TSC2111 sets a flag in the read only control register 0CH/page 1, which
gets cleared after the flag is read. The TSC2111 can also be configured to send an active high interrupt over
GPIO1 by setting D9 of control register 0CH/page 1. The duration of the interrupt is approximately 2 ms.
Auxiliary measurement can only be done in hostcontrolled mode.
See the section Conversion Time Calculation for the TSC2111 and subsection Non Touch Measurement
Operation in this data sheet for timing diagram and conversion time calculation
Port Scan
If making measurements of VBAT, AUX1, and AUX2 is desired on a periodic basis, the Port Scan mode can
be used. This mode causes the TSC2111 to sample and convert battery input and both auxiliary inputs. At the
end of this cycle, the battery and auxiliary result registers contain the updated values. Thus, with one write to
the TSC2111, the host can cause three different measurements to be made.
Port Scan can only be done in host-controlled mode. See the section Issues at the end of this data sheet for
details of a known issue with this mode.
See the section Conversion Time Calculation for the TSC2111 and subsection Port Scan Operation in this data
sheet for timing diagrams and conversion time calculations.
Buffer Mode
The TSC2111 supports a programmable buffer mode, which is applicable for both touch screen related
conversion (X, Y, Z1, Z2) and nontouch screen related conversion (BAT, AUX1, AUX2, TEMP1, TEMP2). Buffer
mode is implemented using a circular FIFO with a depth of 64. The number of interrupts required to be serviced
by a host processor can be reduced significantly buffer mode. Buffer mode can be enabled using control register
02H/page1.
Figure 35. Circular Buffer
Converted data is automatically written into the FIFO. To control the writing, reading and interrupt process, a
write pointer (WRPTR), a read pointer (RDPTR) and a trigger pointer (TGPTR) are used. The read pointer
always shows the location, which will be read next. The write pointer indicates the location, in which the next
相關PDF資料
PDF描述
TSC2117IRGZR SPECIALTY CONSUMER CIRCUIT, QCC48
TSC2117IRGZT SPECIALTY CONSUMER CIRCUIT, QCC48
TSC2300IPAGG4 SPECIALTY CONSUMER CIRCUIT, PQFP64
TSC2300IPAGR SPECIALTY CONSUMER CIRCUIT, PQFP64
TSC2300IPAG SPECIALTY CONSUMER CIRCUIT, PQFP64
相關代理商/技術參數
參數描述
TSC-2-1-15 制造商:Micrel Inc 功能描述:
TSC2117 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power Audio Codec With Embedded miniDSP, Stereo Class-D Speaker Amplifier, and Smart Four-Wire Touch-Screen Controller
TSC2117EVM-K 功能描述:音頻 IC 開發工具 TSC2117 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TSC2117IRGZR 功能描述:觸摸屏轉換器和控制器 4-Wire Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
TSC2117IRGZT 功能描述:觸摸屏轉換器和控制器 4-Wire Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20