- 您現在的位置：買賣IC網 > PDF目錄379479 > UCC28510-17 (Texas Instruments, Inc.) ADVANCED PFC/PWW COMBINATION CONTROLLER WITH TRAILING-EDGE/TRAILING-EDGE MODULATION PDF資料下載
參數資料
| 型號： | UCC28510-17 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | ADVANCED PFC/PWW COMBINATION CONTROLLER WITH TRAILING-EDGE/TRAILING-EDGE MODULATION |
| 中文描述： | 高級式PFC / PWW組合控制器，TRAILING-EDGE/TRAILING-EDGE調制 |
| 文件頁數： | 9/39頁 |
| 文件大小： | 725K |
| 代理商： | UCC28510-17 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
SLUS517B DECEMBER 2002 REVISED AUGUST 2004
9
www.ti.com
DETAILED PIN DESCRIPTIONS (CONTINUED)
The maximum duty ratio is modestly dependent on the switching frequency. A more accurate estimate of the
maximum duty cycle that is valid over the full range of switching frequencies (65 kHz to 600 kHz) is given by:
D
MAX
0.26
4.4
10
8
Hz
f
S
V
DX
V
6.9
10
8
Hz
f
S
0.31
where, f
S
is the oscillator frequency measured at CT_BUFF in Hz
This pin can also be used to set D
MAX
to 0 by setting V
DX
less than 0.7 V.
GND (Pin 6):
Signal ground for the integrated circuit. All voltages measured with respect to ground are
referenced to this pin. The bypass capacitors for VCC and VREF should connect to this pin with as little lead
length as possible. PWRGND must be externally connected to this pin. For best results, use a single small circuit
trace to electrically connect between the circuits that use the GND return path and the circuits that use the
PWRGND return path.
GT1 (Pin 12):
A 2-A peak source and 3-A peak sink current totem pole MOSFET gate driver for the PFC stage.
Some overshoot at GT1 can be expected when driving a capacitive load, but adding a minimal series resistor
of about 2
between GT1 and the external MOSFET gate can reduce this overshoot. GT1 is disabled unless
VCC is outside the UVLO region and VREF is on.
GT2 (Pin 10):
A 2-A peak source and 3-A peak sink current totem pole MOSFET gate driver for the PWM stage,
identical to the driver at GT1.
IAC (Pin 18):
This multiplier input senses the rectified ac line voltage. A resistor between IAC and the line
voltage converts the instantaneous line voltage waveform into a current input for the analog multiplier. The
recommended maximum IAC current is 500
μ
A.
ISENSE1 (Pin 16):
This pin is the non-inverting input terminal of the current amplifier. Connect a resistor
between this pin and the grounded side of the PFC stage current sensing resistor. The resistor connected to
this pin should have a value that equals the value of the resistor that is connected between the MOUT pin and
the ungrounded side of the PFC current sense resistor.
ISENSE2 (Pin 8):
A voltage across the PWM stage external current sense resistor generates the input signal
to this pin, with the peak limit threshold set to 1.3 V for peak current mode control. An internal 1.5-V level shift
between ISENSE2 and the input to the PWM comparator provides greater noise immunity. The oscillator ramp
can also be summed into this pin for slope compensation. Figure 36 shows the typical relationship of the
capacitance on the ISENSE2 pin and the minimum controllable limit of the pulse width on the gate2 output. If
the V
ERR
is at the voltage that corresponds to a minimum controllable duty cycle and then is reduced further
the pulse width collapses to near zero.
MOUT (Pin 17):
The output of the multiplier and the input to the current amplifier in the PFC stage are internally
connected at this pin. Set the power range of the PFC stage with a resistor tied between the MOUT pin and the
non-grounded end of the PFC current sense resistor. Connect impedance between the MOUT pin and the
CAOUT pin to compensate the PFC current control loop. The multiplier output is a current and the current
amplifier input is high impedance. The multiplier output current is given by:
I
MOUT
V
VAOUT
1.0
I
IAC
K
V
VFF
2
where, K is the multiplier gain constant, in volts
1
.
PKLMT (Pin 14):
Program the peak current limit of the PFC stage using this pin. The threshold for peak limit
is 0 V. Use a resistor divider between VREF and the non-grounded side of the PFC current sense resistor in
order to shift the level of this signal to a voltage that corresponds to the desired overcurrent threshold voltage,
measured across the PFC current sense resistor.
PWRGND (Pin 11):
Ground for the output drivers at GT1 and GT2. This ground should be tied to GND externally
via a single Kelvin connection.
相關PDF資料 |
PDF描述 |
|---|---|
| UCC38517 | ADVANCED PFC/PWM COMBINA CONTROLLERS |
| UCC28517N | ADVANCED PFC/PWM COMBINATION CONTROLLERS |
| UCC2882-1 | Average Current Mode Synchronous Controller With 5-Bit DAC |
| UCC2882 | Average Current Mode Synchronous Controller With 5-Bit DAC |
| UCC2882- | Average Current Mode Synchronous Controller With 5-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC28510DW | 功能描述:功率因數校正 IC Advanced PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| UCC28510DWG4 | 功能描述:功率因數校正 IC Advanced PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| UCC28510DWR | 功能描述:功率因數校正 IC Advanced PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| UCC28510DWRG4 | 功能描述:功率因數校正 IC Advanced PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| UCC28510N | 功能描述:功率因數校正 IC Advanced PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。