- 您現在的位置：買賣IC網 > PDF目錄359318 > V3020 (Electronic Theatre Controls, Inc.) Ultra Low Power 1-Bit 32 kHz RTC PDF資料下載
參數資料
| 型號： | V3020 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Ultra Low Power 1-Bit 32 kHz RTC |
| 中文描述： | 超低功耗1位32 kHz的時鐘 |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 470K |
| 代理商： | V3020 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁
Clock and Calendar
The Time and date addresses in the RAM (see Table 6) provide
access to the seconds, minutes, hours, day of month, month,
year, week day, and week number. These parameters have the
ranges indicated on Table 6 and are in BCD format. If a
parameter is found to be out of range, it will be cleared on its
being next incremented. The V3020 incorporates leap year
correction and week number calculation. The week number
changes only at the incrementation of the day number from 7 to
1. If week 52 day 7 falls on the 25th, 26th or 27th of December,
then the week number will change to 0 otherwise it will be week
1. Week days are numbered from 1 to 7 with Monday as 1.
Reading of the current time and date must be preceded by a
Copy_clock_to_RAM command. The time and date status bits
11
will indicate which time and date addresses changed since the
last time the command was used (see Fig. 11). The time and
date from the last Copy_clock_to_RAM command is held
unchanged in the RAM, except when power (V
totally. To change the current time and date in the clock, the
desired time and date must first be written to the RAM, the time
set lock bit cleared, and then a Copy_RAM_to_clock command
sent (see Fig. 12). The time set lock bit can be used to prevent
unauthorized setting of the clock.
) has failed
DD
Frequency Measurement
Setting bit 0 at address 0 will put a pulsed current source (25
m
A)
onto the I/O pin, when the device is not chip selected (i.e. CS
input high). The current source will be pulsed on/off at 256 Hz.
The period for ±0 ppm time keeping is 3.90625 ms. To
measure the frequency signal on pin I/O, the data bus must be
high impedance. The best way to ensure this is to hold the
microprocessor and peripherals in reset mode while measuring
the frequency. The clarity of the signal measured at pin I/O will
depend on both the probe input impedance (typically 1 M
W
)
and the magnitude of the leakage current from other devices
driving the line connected to pin I/O. If the signal measured is
unclear, put a 200 k
W
resistor from pin I/O to V . It should be
noted that the magnitude of the current source (25
m
A) is not
sufficient to drive the data bus line in case of any other device
driving the line, but it is sufficient to take the line to a high logic
level when the data bus is in high impedance.
Use a crystal of nominal C = 8.2 pF as specified in the section
“Operating Conditions”. The MX series from Microcrystal is
recommended. The accuracy of the time keeping is dependent
upon the frequency tolerance and the load capacitance of the
crystal. 11.57 ppm corresponds to one second a day.
Setting the Current Time and Date
Fig. 12
Write seconds, minutes, hours, day
of month, week day, month, year
and week number to the RAM
Clear the time set lock bit, addr. 0, bit 4
Send copy_RAM_to_clock command,
addr. E hex
Set the time set lock bit, addr. 0, bit 4
Reading the Current Time and Date
Fig. 11
Send copy_clock_to_RAM addr. F hex
Read time and data status bits, addr. 1
Is
the seconds
status bit set,
addr. 1,
bit 0
No
Yes
Current time and date
Read seconds, addr. 2
Is
the minutes
status bit set,
addr. 1,
bit 1
Similar for hours, day of month,
week day, month, year and
week number
Read minutes addr. 3
Yes
No
V3020
R
相關PDF資料 |
PDF描述 |
|---|---|
| V30208S | Ultra Low Power 1-Bit 32 kHz RTC |
| V30208TSS | Ultra Low Power 1-Bit 32 kHz RTC |
| V3021 | Ultra Low Power 1-Bit 32 kHz RTC |
| V30218P | Ultra Low Power 1-Bit 32 kHz RTC |
| V30218S | Ultra Low Power 1-Bit 32 kHz RTC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V30200C | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual High-Voltage Trench MOS Barrier Schottky Rectifier Ultra Low VF = 0.526 V at IF = 5 A |
| V30200C_09 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual High-Voltage Trench MOS Barrier Schottky Rectifier |
| V30200C-E3/4W | 功能描述:肖特基二極管與整流器 30 Amp 200 Volt Dual TrenchMOS RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| V30200C-E3-4W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual High-Voltage Trench MOS Barrier Schottky Rectifier |
| V30202C-M3/4W | 功能描述:Diode Array 1 Pair Common Cathode Schottky 200V 15A Through Hole TO-220-3 制造商:vishay semiconductor diodes division 系列:TMBS? 包裝:管件 零件狀態:* 二極管配置:1 對共陰極 二極管類型:肖特基 電壓 - DC 反向（Vr）（最大值）:200V 電流 - 平均整流（Io）（每二極管）:15A 不同 If 時的電壓 - 正向（Vf）:880mV @ 15A 速度:快速恢復 = 200mA（Io） 反向恢復時間（trr）:- 不同?Vr 時的電流 - 反向漏電流:250μA @ 200V 安裝類型:通孔 封裝/外殼:TO-220-3 供應商器件封裝:TO-220AB 標準包裝:50 |
發布緊急采購，3分鐘左右您將得到回復。