參數資料
型號: V54C365804VB
廠商: Mosel Vitelic, Corp.
英文描述: High Performance PC100/125MHz 3.3 Volt 8M X 8 Synchronous DRAM(3.3V高性能pc100/125MHz 8Mx8同步動態RAM)
中文描述: 高性能PC100/125MHz 3.3伏8米× 8同步DRAM(3.3V的高性能pc100/125MHz 8Mx8同步動態RAM)的
文件頁數: 9/54頁
文件大?。?/td> 457K
代理商: V54C365804VB
MOSEL V ITELIC
V54C365804VB
9
V54C365804VB Rev. 1.1 February 1999
operation. If CA10 is high when a Read Command
is issued, the
Read with Auto-Precharge
is initiated. The SDRAM automatically enters the
precharge operation one clock before the last data
out for CAS latencies 2, two clocks for CAS laten-
cies 3 and three clocks for CAS latencies 4. If
CAS10 is high when a Write Command is issued,
the
Write with Auto-Precharge
ed. The SDRAM automatically enters the precharge
operation a time delay equal to t
time) after the last data in.
function
function is initiat-
WR
(Write recovery
Precharge Command
There is also a separate precharge command
available. When RAS and WE are low and CAS is
high at a clock timing, it triggers the precharge
operation. Three address bits, BA0, BA1 and A10
are used to define banks as shown in the following
list. The precharge command can be imposed one
clock before the last data out for CAS latency = 2,
two clocks before the last data out for CAS latency
= 3 and three clocks before the last data out for CAS
latency= 4. Writes require a time delay twr from the
last data out to apply the precharge command.
Bank Selection by Address Bits:
Burst Termination
Once a burst read or write operation has been ini-
tiated, there are several methods in which to termi-
nate the burst operation prematurely. These
methods include using another Read or Write Com-
mand to interrupt an existing burst operation, use a
Precharge Command to interrupt a burst cycle and
close the active bank, or using the Burst Stop Com-
mand to terminate the existing burst operation but
leave the bank open for future Read or Write Com-
mands to the same page of the active bank. When
interrupting a burst with another Read or Write
Command care must be taken to avoid I/O conten-
tion. The Burst Stop Command, however, has the
fewest restrictions making it the easiest method to
use when terminating a burst operation before it has
been completed. If a Burst Stop command is issued
during a burst write operation, then any residual
data from the burst write cycle will be ignored. Data
that is presented on the I/O pins before the Burst
Stop Command is registered will be written to the
memory.
Driver Operating Options
Note:
The timing parameters are in clk cycle.
A10
BA0
BA1
0
0
0
Bank 0
0
0
1
Bank 1
0
1
0
Bank 2
0
1
1
Bank 3
1
X
X
all Banks
Bus
Frequency 8PC
-8
-10
CL
t
RCD
t
RP
t
RC
100 MHz
X
2
2
2
7
100 MHz
X
3
2
3
8
100 MHz
X
3
2
2
7
100 MHz
X
X
3
3
3
8
66 MHz
X
X
X
2
2
2
7
66 MHz
X
X
X
2
2
3
8
66 MHz
X
X
X
2
2
3
8
相關PDF資料
PDF描述
V54C365804VC HIGH PERFORMANCE 143/133/125 MHz 3.3 VOLT 8M X 8 SYNCHRONOUS DRAM 4 BANKS X 2Mbit X 8
V54C365804VD HIGH PERFORMANCE 143/133/125 MHz 3.3 VOLT 8M X 8 SYNCHRONOUS DRAM 4 BANKS X 2Mbit X 8
V551HA40 Varistor Products - High Energy Industrial
V55C2128164VB 128Mbit LOW-POWER SDRAM 2.5 VOLT, TSOP II / BGA PACKAGE 8M X 16
V55C2128164VT 128Mbit LOW-POWER SDRAM 2.5 VOLT, TSOP II / BGA PACKAGE 8M X 16
相關代理商/技術參數
參數描述
V54C365804VC 制造商:MOSEL 制造商全稱:MOSEL 功能描述:HIGH PERFORMANCE 143/133/125 MHz 3.3 VOLT 8M X 8 SYNCHRONOUS DRAM 4 BANKS X 2Mbit X 8
V54C365804VD 制造商:MOSEL 制造商全稱:MOSEL 功能描述:HIGH PERFORMANCE 143/133/125 MHz 3.3 VOLT 8M X 8 SYNCHRONOUS DRAM 4 BANKS X 2Mbit X 8
V5-5/RK 4-0.3/0.3/0.3 制造商:TURCK Inc 功能描述:Cordset, Splitter, M12 Female Straight x 3, 4 Wire, 5m, PVC, Yellow, U0986-00
V5-5/RK 4-1/1/1 制造商:TURCK Inc 功能描述:Cordset, Splitter, M12 Female Straight x 3, 4 Wire, 5m, PVC, Yellow, U-16415
V5509 制造商:Assmann Electronics Inc 功能描述:Old Part V5509^ASSMANN