- 您現在的位置：買賣IC網 > PDF目錄11591 > VNC2-48L1B-REEL (FTDI, Future Technology Devices International Ltd)IC USB HOST/DEVICE CTRL 48-LQFP PDF資料下載
參數資料
| 型號： | VNC2-48L1B-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 16/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB HOST/DEVICE CTRL 48-LQFP |
| 應用說明： | Vinculum-II IO Cell Description AppNote Vinculum-II Debug Interface Description AppNote Vinculum-II IO Mux Explained AppNote Vinculum-II PWM Example AppNote Migrating Vinculum Designs AppNote |
| 特色產品： | Vinculum VNC2 |
| 標準包裝： | 1 |
| 系列： | Vinculum-II |
| 控制器類型： | USB 2.0 控制器 |
| 接口： | USB，主機/設備配置，UART，SPI，PWM，閃存 256K，DMA 4CH |
| 電源電壓： | 1.62 V ~ 1.98 V |
| 電流 - 電源： | 25mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 其它名稱： | 768-1049-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
23
Copyright 2009-2011 Future Technology Devices International Limited
Datasheet
Vinculum-II Embedded Dual USB Host Controller IC
Version 1.5
Document No.: FT_000138 Clearance No.: FTDI# 143
4.2.5 Peripheral DMA Modules 0, 1, 2 & 3
The peripheral DMA has the capability to transfer data to and from an I/O device. The CPU can offload
the transfer of data between the processor and the peripheral freeing the CPU to execute other
instructions.
The DMA module collects or transmits data from memory to an I/O address space, it is also capable of
copying data in memory and transferring it to another location.
The DMA is not accessible by the user as it automatically controlled by the CPU.
4.2.6 RAM Module
The RAM module consists of 16k bytes on-chip (4k x 32-bits) data memory. The RAM is byte addressable.
4.2.7 Peripheral Interface Modules
VNC2 has nine peripheral interface modules. Full descriptions of each module are described in section 6.
Debugger Interface
UART
PWM
FIFO
SPI Master
SPI Slave 0 & 1
GPIO - General purpose I/O pins
General purpose timers
4.2.8 USB Transceivers 0 and 1
Two USB transceiver cells provide the physical USB device interface supporting USB 1.1 and USB 2.0
standards. Low-speed and full-speed USB data rates are supported. Each output driver provides +3.3V
level slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB
DATA IN, SE0 and USB Reset condition detection. These cells also include integrated internal USB pull-up
or pull-down resistors as required for host or slave mode.
4.2.9 USB Host / Device Controllers
These blocks handle the parallel-to-serial and serial-to-parallel conversion of the USB physical layer. This
includes bit stuffing, CRC generation, USB frame generation and protocol error checking. The Host /
Device controller is autonomous and therefore requires limited load from the CPU.
4.2.10 12MHz Oscillator
The 12MHz Oscillator cell generates a 12MHz reference clock input to the Clock Multiplier PLL from an
external 12MHz crystal. The external crystal is connected across Pin 4 – XTIN and Pin 5 – XTOUT in the
configuration shown in Figure 10.1.
4.2.11 Power Saving Modes and Standby mode.
VNC2 can be set to operate in three frequencies allowing the user to select a slower speed to reduce
power consumption. Three operating frequencies available are 12MHz, 24MHz and normal operation of
48MHz. These operating modes can be configured using the RTOS. Full details are available in the RTOS
manual available from the FTDI website.
When a particular peripheral is not used, it is powered down internally thus saving power.
Standby mode is available under firmware control, this mode puts the VNC2 in a state with no clocks
running or system blocks powered. The device will wake up out of this mode by toggling any of the
following signals: USB0/1 DP or DM, SPI slave 0 select (spi_s0_ss# ), SPI slave 1select(spi_s1_ss# ) or
UART ring indicator (uart_ri#).
相關PDF資料 |
PDF描述 |
|---|---|
| V72A48C400BL3 | CONVERTER MOD DC/DC 48V 400W |
| V72A48C400B3 | CONVERTER MOD DC/DC 48V 400W |
| VNC2-48Q1B-REEL | IC USB HOST/DEVICE CTRL 48-QFN |
| V72A48C400B2 | CONVERTER MOD DC/DC 48V 400W |
| 081-120 | CONN RCPT MINI-UHF BULKHEAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VNC2-48L1B-TRAY | 功能描述:USB 接口集成電路 Vinculum-II Dual Host/Dev IC LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| VNC2-48L1C-REEL | |
| VNC2-48L1C-TRAY | 功能描述:IC USB HOST/DEVICE CTRL 48-LQFP 制造商:ftdi, future technology devices international ltd 系列:Vinculum-II 包裝:托盤 零件狀態:在售 協議:USB 功能:控制器 接口:SPI，UART 標準:USB 2.0 電壓 - 電源:1.8V， 3.3V 電流 - 電源:25mA 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 供應商器件封裝:48-LQFP（7x7） 標準包裝:250 |
| VNC2-48Q1A-REEL | 功能描述:USB 接口集成電路 Obsolete see VNC2-48Q1B-REEL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| VNC2-48Q1A-TRAY | 功能描述:USB 接口集成電路 Obsolete see VNC2-48Q1B-TRAY RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。