- 您現在的位置：買賣IC網 > PDF目錄361790 > W6694CD (WINBOND ELECTRONICS CORP) USB Bus ISDN S/T-Controller PDF資料下載
參數資料
| 型號： | W6694CD |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | USB Bus ISDN S/T-Controller |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM, PLASTIC, LQFP-48 |
| 文件頁數： | 29/42頁 |
| 文件大?。?/td> | 567K |
| 代理商： | W6694CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Preliminary Data Sheet
W6694A USB-ISDN S/T-Controller
-29-
Publication Release Date: May, 2001
Revision 1.03
GRLP GCI Mode Remote Loop back
Setting this bit to 1 activates the remote loop back function. The 2B+D channels data received from the GCI bus
interface are looped to the transmitted channels.
SPU
Software Power Up
PD
Power Down
SPU
PD
0
1
After U transceiver power down, W6694A will receive the indication DC (Deactivation Confirmation) from
GCI bus and then software has to set SPU
→
0, PD
→
1 to acknowledge U transceiver, by pulling GCIDU
line to HIGH. W6694A remains normal operation.
1
0
Setting SPU
→
1, PD
→
0 will pull the GCI bus GCIDU line to LOW. This will enforce connected layer 1
devices (U transceiver) to deliver GCI bus clocking.
0
0
After reception of the indication PU (Power Up indication) the reaction of the microprocessor should be:
-
To write an AR (Activate Request command) as C/I command code in the CIX register.
- To reset the SPU bit and wait for the following ICC (indication code change) interrupt.
1
1
Unused.
GE
GCI Mode Enable
Setting this bit to 1 will enable the GCI bus interface. In the same time, the S/T layer 1 function is disabled.
Description
8.3.2 Monitor Channel Control Register
Value after reset: 00h
7
6
0
0
MRIE Monitor Channel 0 Receive Interrupt Enable
Monitor channel interrupt status MDR, MER generation is enabled (1) or masked (0).
MRC MR Bit Control
Determines the value of the MR bit:
0: MR bit always 1. In addition, the MDR interrupt is blocked, except for the first byte of a packet (if MRIE=1).
1: MR internally controlled according to Monitor channel protocol. In addition, the MDR interrupt is enabled for all
bytes according to the Monitor channel protocol (if MRIE=1).
MXIE Monitor Channel Transmit Interrupt Enable
Monitor interrupt status MDA, MAB generation is enabled (1) or masked (0).
MXC MX Bit Control
Determines the value of the MX bit:
0: MX always 1.
1: MX internally controlled according to Monitor channel protocol.
MOCR
Read/Write Address 07h
5
0
4
0
3
2
1
0
MRIE
MRC
MXIE
MXC
相關PDF資料 |
PDF描述 |
|---|---|
| W7020 | Telecommunication IC |
| W722 | Controller Miscellaneous - Datasheet Reference |
| W72963APOLLOELITE | BEWEGUNGSMELDER IR REICHW 12M |
| W72M64V-XBX | Flash MCP |
| W72M64VK120BM | 2Mx64 3.3V Simultaneous Operation Flash Multi-Chip Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W66ARX-18 | 制造商:Magnecraft 功能描述: |
| W66MAF185X | 制造商:Panasonic Industrial Company 功能描述:CRT |
| W66R_1G WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W66TX-25 | 制造商:Magnecraft 功能描述: |
| W66TX-29 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。