- 您現在的位置：買賣IC網 > PDF目錄361790 > W741E200 4-Bit Microcontroller PDF資料下載
參數資料
| 型號： | W741E200 |
| 英文描述： | 4-Bit Microcontroller |
| 中文描述： | 4位微控制器 |
| 文件頁數： | 24/84頁 |
| 文件大小： | 344K |
| 代理商： | W741E200 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
Preliminary W741E20X
- 24 -
Interrupt Enable Flag (IEF)
The interrupt enable flag is organized as an 8-bit binary register (IEF.0 to IEF.7). These bits are used
to control the interrupt conditions. It is controlled by the MOV IEF, #I instruction. When one of these
interrupts is accepted, the corresponding to the bit of the event flag will be reset, but the other bits are
unaffected. In interrupt subroutine, these interrupts will be disable till the instruction MOV IEF, #I
or EN
INT
is executed again. To enable these interrupts, the instructions MOV IEF, #I or EN INT must be
executed again. Otherwise, these interrupts can be disable by executing DIS INT instruction. The bit
descriptions are as follows:
Note: W means write only.
IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.
IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change at port RC.
IEF.3 is reserved.
w
w
w
1
2
3
IEF
4
w
w
5
6
0
w
w
7
IEF.4 = 1 Interrupt 4 is accepted by a falling edge signal at the INT pin.
IEF.5 = 1 Interrupt 5 is accepted by the serial port received completely.
IEF.6 = 1 Interrupt 6 is accepted by the serial port transmitted completely.
IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.
External INT
The external interrupt INT pin contains a pull-up resistor. When the HEF.4 or IEF.4 flag is set, the
falling edge of the INT pin will execute the hold mode release or interrupt subroutine. A low level on
the INT pin will release the stop mode.
Stop Mode Operation
In stop mode, all operations of the
μ
C cease (including the operation of the oscillator). The
μ
C enters
stop mode when the STOP instruction is executed and exits stop mode when an external trigger is
activated (by a low level on the INT pin or a falling signal on the RC port). When the designated signal
is accepted, the
μ
C awakens and warm-up, and then executes the next instruction.
Stop Mode Wake-up Enable Flag for Ports RC (SEF)
The stop mode wake-up flag for ports RC is organized as an 4-bit binary register (SEF.0 to SEF.3).
Before port RC may be used to make the device exit the stop mode, the content of the SEF must be
set first. The SEF is controlled by the MOV SEF, #I instruction. The bit descriptions are as follows:
Note: W means write only.
SEF 0 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.0
SEF
w
w
w
0
1
2
w
3
相關PDF資料 |
PDF描述 |
|---|---|
| W742C(E)811 | 4-BIT MICROCONTROLLER |
| W742C816 | Microcontroller |
| W742C818 | Microcontroller |
| W742E816 | Microcontroller |
| W742C811 | 4-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W741E201 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E202 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E203 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E204 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
| W741E205 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4-BIT FLASH MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。