- 您現在的位置：買賣IC網 > PDF目錄371190 > X1228V14Z-2.7A (INTERSIL CORP) EXT. DISTANCE DATA CABLE 25 CO PDF資料下載
參數資料
| 型號： | X1228V14Z-2.7A |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | EXT. DISTANCE DATA CABLE 25 CO |
| 中文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO14 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-153AC, TSSOP-14 |
| 文件頁數： | 25/31頁 |
| 文件大?。?/td> | 569K |
| 代理商： | X1228V14Z-2.7A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁
X1228
REV 1.3 3/24/04
Characteristics subject to change without notice.
25 of 31
www.xicor.com
A final application for the ATR control is in-circuit cali-
bration for high accuracy applications, along with a
temperature sensor chip. Once the RTC circuit is pow-
ered up with battery backup, the PHZ output is set at
32.768kHz and frequency drift is measured. The ATR
control is then adjusted to a setting which minimizes
drift. Once adjusted at a particular temperature, it is
possible to adjust at other discrete temperatures for
minimal overall drift, and store the resulting settings in
the EEPROM. Extremely low overall temperature drift
is possible with this method. The Xicor evaluation
board contains the circuitry necessary to implement
this control.
For more detailed operation see Xicor’s application
note AN154 on Xicor’s website at www.xicor.com.
Layout Considerations
The crystal input at X1 has a very high impedance and
will pick up high frequency signals from other circuits
on the board. Since the X2 pin is tied to the other side
of the crystal, it is also a sensitive node. These signals
can couple into the oscillator circuit and produce dou-
ble clocking or mis-clocking, seriously affecting the
accuracy of the RTC. Care needs to be taken in layout
of the RTC circuit to avoid noise pickup. Below in Fig-
ure 15 is a suggested layout for the X1228 device.
Figure 15. Suggested Layout for Xicor RTC in SO-14
The X1 and X2 connections to the crystal are to be
kept as short as possible. A thick ground trace around
the crystal is advised to minimize noise intrusion, but
ground near the X1 and X2 pins should be avoided as
it will add to the load capacitance at those pins. Keep in
mind these guidelines for other PCB layers in the vicin-
ity of the RTC device. A small decoupling capacitor at
the Vcc pin of the chip is mandatory, with a solid con-
nection to ground.
Assembly
Most electronic circuits do not have to deal with
assembly issues, but with the RTC devices assembly
includes insertion or soldering of a live battery into an
unpowered circuit. If a socket is soldered to the board,
and a battery is inserted in final assembly, then there
are no issues with operation of the RTC. If the battery
is soldered to the board directly, then the RTC device
Vback pin will see some transient upset from either sol-
dering tools or intermittent battery connections which
can stop the circuit from oscillating. Once the battery is
soldered to the board, the only way to assure the circuit
will start up is to momentarily (very short period of
time!) short the Vback pin to ground and the circuit will
begin to oscillate.
Oscillator Measurements
When a proper crystal is selected and the layout guide-
lines above are observed, the oscillator should start up
in most circuits in less than one second. Some circuits
may take slightly longer, but startup should definitely
occur in less than 5 seconds. When testing RTC cir-
cuits, the most common impulse is to apply a scope
probe to the circuit at the X2 pin (oscillator output) and
observe the waveform. DO NOT DO THIS! Although in
some cases you may see a useable waveform, due to
the parasitics (usually 10pF to ground) applied with the
scope probe, there will be no useful information in that
waveform other than the fact that the circuit is oscillat-
ing. The X2 output is sensitive to capacitive impedance
so the voltage levels and the frequency will be affected
by the parasitic elements in the scope probe. Applying
a scope probe can possibly cause a faulty oscillator to
start up, hiding other issues (although in the Xicor
RTC’s, the internal circuitry assures startup when
using the proper crystal and layout).
C1
0.1
μ
F
XTAL1
32.768kGz
U1
R1 10k
X1228
相關PDF資料 |
PDF描述 |
|---|---|
| X1228S14Z-2.7T1 | EXT DIST RS232 DATA CBL DB25 MALE - DB25 FEMALE |
| X1228V14I-2.7A | RTC Module With CPU Supervisor |
| X1228V14I-4.5A | DIODE 05 TVS SO8 |
| X1228V14IZ | RTC Module With CPU Supervisor |
| X1228V14IZ-2.7A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1228V14Z-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1228ZY WAF | 制造商:Intersil Corporation 功能描述: |
| X122K | 制造商:IQD Frequency Products 功能描述:CRYSTAL OSCILLATOR 12.288000MHZ |
| X122-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| X123-133.33M | 制造商:CONNOR-WINFIELD 制造商全稱:Connor-Winfield Corporation 功能描述:5.0x7.0mm Surface Mount LVCMOS Clock Oscillator Series |
發布緊急采購，3分鐘左右您將得到回復。