- 您現在的位置：買賣IC網 > PDF目錄297797 > X4163S8Z (INTERSIL CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | X4163S8Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | ROHS COMPLIANT, SOIC-8 |
| 文件頁數： | 19/22頁 |
| 文件大?。?/td> | 342K |
| 代理商： | X4163S8Z |
6
FN8120.2
November 26, 2007
Setting the VTRIP Voltage
This procedure is used to set the VTRIP to a higher or
lower voltage value. It is necessary to reset the trip
point before setting the new value.
To set the new VTRIP voltage, start by setting the WEL
bit in the control register, then apply the desired VTRIP
threshold voltage to the VCC pin and the programming
voltage, VP, to the WP pin and 2 byte address and 1
byte of “00” data. The stop bit following a valid write
operation initiates the VTRIP programming sequence.
Bring WP LOW to complete the operation.
Resetting the VTRIP Voltage
This procedure is used to set the VTRIP to a “native”
voltage level. For example, if the current VTRIP is 4.4V
and the new VTRIP must be 4.0V, then the VTRIP must
be reset. When VTRIP is reset, the new VTRIP is some-
thing less than 1.7V. This procedure must be used to
set the voltage to a lower value.
To reset the new VTRIP voltage start by setting the
WEL bit in the control register, apply VCC and the pro-
gramming voltage, VP, to the WP pin and 2 byte
address and 1 byte of “00” data. The stop bit of a valid
write operation initiates the VTRIP programming
sequence. Bring WP LOW to complete the operation.
Figure 2. Reset VTRIP Level Sequence (VCC > 3V. WP = 12–15V, WEL bit set)
Figure 3. Sample VTRIP Reset Circuit
01 2 3 45 67
SCL
SDA
A0h
01 2 3 45 67
00h
WP
VP = 12-15V
01 2 3 45 67
03h
01 2 3 4 5 6 7
00h
1
2
3
4
8
7
6
5
X4163
VTRIP
Adj.
VP
RESET
4.7K
SDA
SCL
C
Adjust
Run
SOIC
X4163, X4165
相關PDF資料 |
PDF描述 |
|---|---|
| X4165V8-2.7 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165S8-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5001S8-1.8 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5043V14I-2.7A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| X5045M8I-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4163S8Z-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163S8Z-2.7A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163S8Z-4.5A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163V8 | 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4163V8-2.7 | 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。