參數資料
型號: X4163S8Z
廠商: INTERSIL CORP
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
封裝: ROHS COMPLIANT, SOIC-8
文件頁數: 22/22頁
文件大?。?/td> 342K
代理商: X4163S8Z
9
FN8120.2
November 26, 2007
Writing to the Control Register
Changing any of the nonvolatile bits of the control reg-
ister requires the following steps:
– Write a 02H to the Control Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation pre-
ceeded by a start and ended with a stop).
– Write a 06H to the Control Register to set both the
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation preceeded by a start
and ended with a stop).
– Write a value to the Control Register that has all the
control bits set to the desired state. This can be rep-
resented as 0xys t01r in binary, where xy are the
WD bits. (Operation preceeded by a start and ended
with a stop). Since this is a nonvolatile write cycle it
will take up to 10ms to complete. The RWEL bit is
reset by this cycle and the sequence must be
repeated to change the nonvolatile bits again. If bit 2
is set to ‘1’ in this third step (0xys t11r) then the
RWEL bit is set, but the BP2, BP1, BP0, WD1 and
WD0 bits remain unchanged. Writing a second byte
to the control register is not allowed. Doing so aborts
the write operation and returns a NACK.
– A read operation occurring between any of the previ-
ous operations will not interrupt the register write
operation.
– The RWEL bit cannot be reset without writing to the
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
To illustrate, a sequence of writes to the device con-
sisting of [02H, 06H, 02H] will reset all of the nonvola-
tile bits in the Control Register to 0. A sequence of
[02H, 06H, 06H] will leave the nonvolatile bits
unchanged and the RWEL bit remains set.
SERIAL INTERFACE
Serial Interface Conventions
The device supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter, and the receiving device
as the receiver. The device controlling the transfer is
called the master and the device being controlled is
called the slave. The master always initiates data
transfers, and provides the clock for both transmit and
receive operations. Therefore, the devices in this fam-
ily operate as slaves in all applications.
Serial Clock and Data
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See
Figure 5. Valid Data Changes on the SDA Bus
SCL
SDA
Data Stable
Data Change
Data Stable
X4163, X4165
相關PDF資料
PDF描述
X4165V8-2.7 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
X4165S8-4.5A 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
X5001S8-1.8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
X5043V14I-2.7A 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14
X5045M8I-4.5A 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
相關代理商/技術參數
參數描述
X4163S8Z-2.7 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM
X4163S8Z-2.7A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM
X4163S8Z-4.5A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM
X4163V8 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:8-TSSOP 包裝:管件
X4163V8-2.7 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:8-TSSOP 包裝:管件