- 您現在的位置：買賣IC網 > PDF目錄9190 > X9250UV24IZ-2.7 (Intersil)IC XDCP QUAD 256TP 50K 24-TSSOP PDF資料下載
參數資料
| 型號： | X9250UV24IZ-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC XDCP QUAD 256TP 50K 24-TSSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 62 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
6
FN8165.3
August 29, 2006
The four high order bits of the instruction byte specify
the operation. The next two bits (R1 and R0) select
one of the four registers that is to be acted upon when
a register oriented instruction is issued. The last two
bits (P1 and P0) selects which one of the four
potentiometers is to be affected by the instruction.
Four of the ten instructions are two bytes in length and
end with the transmission of the instruction byte.
These instructions are:
– XFR Data Register to Wiper Counter Register—This
transfers the contents of one specified Data Register
to the associated Wiper Counter Register.
– XFR Wiper Counter Register to Data Register—This
transfers the contents of the specified Wiper
Counter Register to the specified associated Data
Register.
– Global XFR Data Register to Wiper Counter Regiter—
This transfers the contents of all specified Data Reg-
isters to the associated Wiper Counter Registers.
– Global XFR Wiper Counter Register to Data Regiter—
This transfers the contents of all Wiper Counter
Registers to the specified associated Data Regis-
ters.
The basic sequence of the two byte instructions is
illustrated in Figure 4. These two-byte instructions
exchange data between the WCR and one of the Data
Registers. A transfer from a Data Register to a WCR is
essentially a write to a static RAM, with the static RAM
controlling the wiper position. The response of the
wiper to this action will be delayed by tWRL. A transfer
from the WCR (current wiper position), to a Data
Register is a write to nonvolatile memory and takes a
minimum of tWR to complete. The transfer can occur
between one of the four potentiometers and one of its
associated registers; or it may occur globally, where
the transfer occurs between all potentiometers and one
associated register.
Five instructions require a three-byte sequence to
complete. These instructions transfer data between
the host and the X9250; either between the host and
one of the data registers or directly between the host
and the Wiper Counter Register. These instructions
are:
– Read Wiper Counter Register—read the current
wiper position of the selected pot,
– Write Wiper Counter Register—change current
wiper position of the selected pot,
– Read Data Register—read the contents of the
selected data register;
– Write Data Register—write a new value to the
selected data register.
– Read Status—This command returns the contents
of the WIP bit which indicates if the internal write
cycle is in progress.
The sequence of these operations is shown in Figure
The final command is Increment/Decrement. It is
different from the other commands, because it’s length
is indeterminate. Once the command is issued, the
master can clock the selected wiper up and/or down in
one resistor segment steps; thereby, providing a fine
tuning capability to the host. For each SCK clock pulse
(tHIGH) while SI is HIGH, the selected wiper will move
one resistor segment towards the VH/RH terminal.
Similarly, for each SCK clock pulse while SI is LOW,
the selected wiper will move one resistor segment
towards the VL/RL terminal. A detailed illustration of the
sequence and timing for this operation are shown in
X9250
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E24F35PD | CONN RCPT 128POS BOX MNT W/PINS |
| X9259UV24IZ-2.7 | IC XDCP QUAD 256TAP 50K 24-TSSOP |
| X9259TV24IZ-2.7 | IC XDCP QUAD 256TAP 100K 24TSSOP |
| MS27508E24A35PC | CONN RCPT 128POS BOX MNT W/PINS |
| VI-2V1-MX-B1 | CONVERTER MOD DC/DC 12V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9250UV24Z-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometers |
| X9250UZ24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DIGITAL POTENTIOMETER|CMOS|BGA|24PIN|PLASTIC |
| X9250UZ24-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DIGITAL POTENTIOMETER|CMOS|BGA|24PIN|PLASTIC |
| X9250UZ24I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DIGITAL POTENTIOMETER|CMOS|BGA|24PIN|PLASTIC |
| X9250UZ24I-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DIGITAL POTENTIOMETER|CMOS|BGA|24PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。