- 您現在的位置：買賣IC網 > PDF目錄371293 > X9400YZ24 Quad Digitally Controlled Potentiometers (XDCP) PDF資料下載
參數資料
| 型號： | X9400YZ24 |
| 元件分類： | 數字電位計 |
| 英文描述： | Quad Digitally Controlled Potentiometers (XDCP) |
| 中文描述： | 四重?cái)?shù)控電位器（數字電位器） |
| 文件頁數： | 11/22頁 |
| 文件大?。?/td> | 150K |
| 代理商： | X9400YZ24 |
X9400
Characteristics subject to change without notice.
11 of 22
REV 1.1.4 10/11/02
www.xicor.com
D.C. OPERATING CHARACTERISTICS
(Over the recommended operating conditions unless otherwise specified.)
ENDURANCE AND DATA RETENTION
CAPACITANCE
POWER-UP TIMING
Symbol
I
CC1
Parameter
Limits
Typ.
Test Conditions
f
SCK
= 2MHz, SO = Open,
Other Inputs = V
SS
f
SCK
= 2MHz, SO = Open,
Other Inputs = V
SS
SCK = SI = V
SS
, Addr. = V
SS
V
IN
= V
SS
to V
CC
V
OUT
= V
SS
to V
CC
Min.
Max.
400
Units
μA
V
CC
supply current (Active)
I
CC2
V
CC
supply current (Nonvol-
atile Write)
V
CC
current (standby)
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
Output LOW voltage
1
mA
I
SB
I
LI
I
LO
V
IH
V
IL
V
OL
1
10
10
μA
μA
μA
V
V
V
V
CC
x 0.7
–0.5
V
CC
+ 0.5
V
CC
x 0.1
0.4
I
OL
= 3mA
Parameter
Minimum endurance
Data retention
Min.
100,000
100
Unit
Data changes per bit per register
years
Symbol
C
OUT
(4)
C
IN
(4)
Test
Max.
8
6
Unit
pF
pF
Test Conditions
V
OUT
= 0V
V
IN
= 0V
Output capacitance (SO)
Input capacitance (A0, A1, SI, and SCK)
Symbol
t
PUR
(5)
t
PUW
(5)
t
R
V
CC
(4)
Parameter
Min.
Max.
1
5
50
Unit
ms
ms
V/msec
Power-up to initiation of read operation
Power-up to initiation of write operation
V
CC
Power up ramp
0.2
POWER UP REQUIREMENTS
(Power Up sequencing
can affect correct recall of the wiper registers)
The preferred power-on sequence is as follows: First
V
CC
, then the potentiometer pins, R
H
, R
L
, and R
W
.
Voltage should not be applied to the potentiometer pins
before V+ or V- is applied. The V
CC
ramp rate specifi-
cation should be met, and any glitches or slope
changes in the V
CC
line should be held to <100mV if
possible. If V
CC
powers down, it should be held below
0.1V for more than 1 second before powering up again
in order for proper wiper register recall. Also, V
CC
should not reverse polarity by more than 0.5V. Recall of
wiper position will not be complete until V
CC
, V+ and V-
reach their final value.
EQUIVALENT A.C. LOAD CIRCUIT
5V
1533
100pF
SDA Output
相關PDF資料 |
PDF描述 |
|---|---|
| X9400YZ24I-2.7 | Quad Digitally Controlled Potentiometers (XDCP) |
| X9400 | RF/Microwave Capacitor; Capacitance:20pF; Capacitance Tolerance:+/- 5%; Series:MC; Capacitor Dielectric Material:Mica; Termination:SMD; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No |
| X9400WP24 | Digital Potentiometer |
| X9400WP24-2.7 | Digital Potentiometer |
| X9400WP24I | Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9400YZ24I-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers (XDCP) |
| X9401 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/SPI Bus |
| X9401_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad, 64 Tap, Digitally Controlled Potentiometer |
| X9401_09 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad, 64 Tap, Digitally Controlled Potentiometer (XDCP?) |
| X94012011-01 | 功能描述:以太網模塊 XPress-Pro SW 94012F 8-Port 10/100TX RoHS:否 制造商:Lantronix 產品:Device Servers 數據速率:300 bps to 921.6 kbps, 10 Mbps, 100 Mbps 接口類型:Ethernet, Serial 工作電源電壓:5 V to 15 V 工作電源電流:133 mA to 400 mA 最大工作溫度:+ 70 C |
發布緊急采購，3分鐘左右您將得到回復。