參數資料
型號: XC2S100-5FGG256C
廠商: Xilinx Inc
文件頁數: 16/99頁
文件大?。?/td> 0K
描述: IC SPARTAN-II FPGA 100K 256-FBGA
標準包裝: 90
系列: Spartan®-II
LAB/CLB數: 600
邏輯元件/單元數: 2700
RAM 位總計: 40960
輸入/輸出數: 176
門數: 100000
電源電壓: 2.375 V ~ 2.625 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 256-BGA
供應商設備封裝: 256-FBGA(17x17)
其它名稱: 122-1302
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
23
R
Master Serial Mode
In Master Serial mode, the CCLK output of the FPGA drives
a Xilinx PROM which feeds a serial stream of configuration
data to the FPGA’s DIN input. Figure 15 shows a Master
Serial FPGA configuring a Slave Serial FPGA from a
PROM. A Spartan-II device in Master Serial mode should
be connected as shown for the device on the left side.
Master Serial mode is selected by a <00x> on the mode
pins (M0, M1, M2). The PROM RESET pin is driven by INIT,
and CE input is driven by DONE. The interface is identical
to the slave serial mode except that an oscillator internal to
the FPGA is used to generate the configuration clock
(CCLK). Any of a number of different frequencies ranging
from 4 to 60 MHz can be set using the ConfigRate option in
the Xilinx software. On power-up, while the first 60 bytes of
the configuration data are being loaded, the CCLK
frequency is always 2.5 MHz. This frequency is used until
the ConfigRate bits, part of the configuration file, have been
loaded into the FPGA, at which point, the frequency
changes to the selected ConfigRate. Unless a different
frequency is specified in the design, the default ConfigRate
is 4 MHz. The frequency of the CCLK signal created by the
internal oscillator has a variance of +45%, –30% from the
specified value.
Figure 17 shows the timing for Master Serial configuration.
The FPGA accepts one bit of configuration data on each
rising CCLK edge. After the FPGA has been loaded, the
data for the next device in a daisy-chain is presented on the
DOUT pin after the rising CCLK edge.
Slave Parallel Mode
The Slave Parallel mode is the fastest configuration option.
Byte-wide data is written into the FPGA. A BUSY flag is
provided for controlling the flow of data at a clock frequency
FCCNH above 50 MHz.
Figure 18, page 24 shows the connections for two
Spartan-II devices using the Slave Parallel mode. Slave
Parallel mode is selected by a <011> on the mode pins (M0,
M1, M2).
If a configuration file of the format .bit, .rbt, or non-swapped
HEX is used for parallel programming, then the most
significant bit (i.e. the left-most bit of each configuration
byte, as displayed in a text editor) must be routed to the D0
input on the FPGA.
The agent controlling configuration is not shown. Typically,
a processor, a microcontroller, or CPLD controls the Slave
Parallel interface. The controlling agent provides byte-wide
configuration data, CCLK, a Chip Select (CS) signal and a
Write signal (WRITE). If BUSY is asserted (High) by the
FPGA, the data must be held until BUSY goes Low.
After configuration, the pins of the Slave Parallel port
(D0-D7) can be used as additional user I/O. Alternatively,
the port may be retained to permit high-speed 8-bit
readback. Then data can be read by de-asserting WRITE.
Figure 17: Master Serial Mode Timing
Serial Data In
CCLK
(Output)
Serial DOUT
(Output)
TDSCK
TCCO
TCKDS
DS001_17_110101
.
Symbol
Description
Units
TDSCK
CCLK
DIN setup
5.0
ns, min
TCKDS
DIN hold
0.0
ns, min
Frequency tolerance with respect to
nominal
+45%, –30%
-
相關PDF資料
PDF描述
AMM24DTBT CONN EDGECARD 48POS R/A .156 SLD
AMM24DTAT CONN EDGECARD 48POS R/A .156 SLD
AMC31DRXS-S734 CONN EDGECARD 62POS DIP .100 SLD
ABC60DRXN-S734 CONN EDGECARD 120PS DIP .100 SLD
ABC60DRXH-S734 CONN EDGECARD 120PS DIP .100 SLD
相關代理商/技術參數
參數描述
XC2S100-5FGG256I 功能描述:IC SPARTAN-II FPGA 100K 256-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S100-5FGG456C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S100-5FGG456I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S100-5PQ208C 功能描述:IC FPGA 2.5V 600 CLB'S 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S1005PQ208I 制造商:Xilinx 功能描述: