參數資料
型號： XC2S15-5VQG100C
廠商： Xilinx Inc
文件頁數： 28/99頁
文件大?。?/td> 0K
描述： IC SPARTAN-II FPGA 15K 100-VQFP
標準包裝： 90
系列： Spartan®-II
LAB/CLB數： 96
邏輯元件/單元數： 432
RAM 位總計： 16384
輸入/輸出數： 60
門數： 15000
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 100-TQFP
供應商設備封裝： 100-VQFP（14x14）
產品目錄頁面： 599 (CN2011-ZH PDF)
其它名稱： 122-1309
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
34
R
Creating Larger RAM Structures
The block RAM columns have specialized routing to allow
cascading blocks together with minimal routing delays. This
achieves wider or deeper RAM structures with a smaller
timing penalty than when using normal routing channels.
Location Constraints
Block RAM instances can have LOC properties attached to
them to constrain the placement. The block RAM placement
locations are separate from the CLB location naming
convention, allowing the LOC properties to transfer easily
from array to array.
The LOC properties use the following form:
LOC = RAMB4_R#C#
RAMB4_R0C0 is the upper left RAMB4 location on the
device.
Conflict Resolution
The block RAM memory is a true dual-read/write port RAM
that allows simultaneous access of the same memory cell
from both ports. When one port writes to a given memory
cell, the other port must not address that memory cell (for a
write or a read) within the clock-to-clock setup window. The
following lists specifics of port and memory cell write conflict
resolution.
If
both
ports
write
to
the
same
memory
cell
simultaneously,
violating
the
clock-to-clock
setup
requirement, consider the data stored as invalid.
If one port attempts a read of the same memory cell
the other simultaneously writes, violating the
clock-to-clock setup requirement, the following occurs.
-
The write succeeds
-
The data out on the writing port accurately reflects
the data written.
-
The data out on the reading port is invalid.
Conflicts do not cause any physical damage.
Single Port Timing
Figure 33 shows a timing diagram for a single port of a block
RAM memory. The block RAM AC switching characteristics
are specified in the data sheet. The block RAM memory is
initially disabled.
At the first rising edge of the CLK pin, the ADDR, DI, EN,
WE, and RST pins are sampled. The EN pin is High and the
WE pin is Low indicating a read operation. The DO bus
contains the contents of the memory location, 0x00, as
indicated by the ADDR bus.
At the second rising edge of the CLK pin, the ADDR, DI, EN,
WR, and RST pins are sampled again. The EN and WE pins
are High indicating a write operation. The DO bus mirrors
the DI bus. The DI bus is written to the memory location
0x0F.
At the third rising edge of the CLK pin, the ADDR, DI, EN,
WR, and RST pins are sampled again. The EN pin is High
and the WE pin is Low indicating a read operation. The DO
bus contains the contents of the memory location 0x7E as
indicated by the ADDR bus.
At the fourth rising edge of the CLK pin, the ADDR, DI, EN,
WR, and RST pins are sampled again. The EN pin is Low
indicating that the block RAM memory is now disabled. The
DO bus retains the last value.
Dual Port Timing
Figure 34 shows a timing diagram for a true dual-port
read/write block RAM memory. The clock on port A has a
longer period than the clock on Port B. The timing
parameter TBCCS, (clock-to-clock setup) is shown on this
diagram. The parameter, TBCCS is violated once in the
diagram. All other timing parameters are identical to the
single port version shown in Figure 33.
TBCCS is only of importance when the address of both ports
are the same and at least one port is performing a write
operation. When the clock-to-clock set-up parameter is
violated for a WRITE-WRITE condition, the contents of the
memory at that location will be invalid. When the
clock-to-clock set-up parameter is violated for a
WRITE-READ condition, the contents of the memory will be
correct, but the read port will have invalid data. At the first
rising edge of the CLKA, memory location 0x00 is to be
written with the value 0xAAAA and is mirrored on the DOA
bus. The last operation of Port B was a read to the same
memory location 0x00. The DOB bus of Port B does not
change with the new value on Port A, and retains the last
read value. A short time later, Port B executes another read
to memory location 0x00, and the DOB bus now reflects the
new memory value written by Port A.
At the second rising edge of CLKA, memory location 0x7E
is written with the value 0x9999 and is mirrored on the DOA
bus. Port B then executes a read operation to the same
memory location without violating the TBCCS parameter and
the DOB reflects the new memory values written by Port A.
相關PDF資料
PDF描述
EEM12DSXN CONN EDGECARD 24POS DIP .156 SLD
RSA43DRMH CONN EDGECARD 86POS .125 SQ WW
TACL335M004H CAP TANT 3.3UF 4V 20% 0603
KA79L05AZBU IC REG LDO -5V .1A TO-92
EEM12DSXH CONN EDGECARD 24POS DIP .156 SLD
相關代理商/技術參數
參數描述
XC2S15-5VQG100I 制造商:Xilinx 功能描述:FPGA SPARTAN-II 15K GATES 432 CELLS 263MHZ 2.5V 100VTQFP - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE
XC2S15-6CS144C 功能描述:IC FPGA 2.5V C-TEMP 144-CSBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-II 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55）
XC2S15-6CS144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S15-6CSG144C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S15-6CSG144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*