參數資料
型號： XC5210-4TQ176I
英文描述： Field Programmable Gate Array (FPGA)
中文描述： 現場可編程門陣列（FPGA）
文件頁數： 22/73頁
文件大?。?/td> 598K
代理商： XC5210-4TQ176I
R
XC5200 Series Field Programmable Gate Arrays
7-104
November 5, 1998 (Version 5.2)
Configuration
Configuration is the process of loading design-specific pro-
gramming data into one or more FPGAs to define the func-
tional operation of the internal blocks and their
interconnections. This is somewhat like loading the com-
mand registers of a programmable peripheral chip.
XC5200-Series devices use several hundred bits of config-
uration data per CLB and its associated interconnects.
Each configuration bit defines the state of a static memory
cell that controls either a function look-up table bit, a multi-
plexer input, or an interconnect pass transistor. The devel-
opment system translates the design into a netlist file. It
automatically partitions, places and routes the logic and
generates the configuration data in PROM format.
Special Purpose Pins
Three configuration mode pins (M2, M1, M0) are sampled
prior to configuration to determine the configuration mode.
After configuration, these pins can be used as auxiliary I/O
connections. The development system does not use these
resources unless they are explicitly specified in the design
entry. This is done by placing a special pad symbol called
MD2, MD1, or MD0 instead of the input or output pad sym-
bol.
In XC5200-Series devices, the mode pins have weak
pull-up resistors during configuration. With all three mode
pins High, Slave Serial mode is selected, which is the most
popular configuration mode. Therefore, for the most com-
mon configuration mode, the mode pins can be left uncon-
nected. (Note, however, that the internal pull-up resistor
value can be as high as 100 k
.) After configuration, these
pins can individually have weak pull-up or pull-down resis-
tors, as specified in the design. A pull-down resistor value
of 3.3k
is recommended.
These pins are located in the lower left chip corner and are
near the readback nets. This location allows convenient
routing if compatibility with the XC2000 and XC3000 family
conventions of M0/RT, M1/RD is desired.
Configuration Modes
XC5200 devices have seven configuration modes. These
modes are selected by a 3-bit input code applied to the M2,
M1, and M0 inputs. There are three self-loading Master
modes, two Peripheral modes, and a Serial Slave mode,
Note :*Peripheral Synchronous can be considered byte-wide
Slave Parallel
which is used primarily for daisy-chained devices. The sev-
enth mode, called Express mode, is an additional slave
mode that allows high-speed parallel configuration. The
coding for mode selection is shown in
Table 10
.
Note that the smallest package, VQ64, only supports the
Master Serial, Slave Serial, and Express modes.A detailed
description of each configuration mode, with timing infor-
mation, is included later in this data sheet. During configu-
ration, some of the I/O pins are used temporarily for the
configuration process. All pins used during configuration
are shown in
Table 13 on page 124
.
Master Modes
The three Master modes use an internal oscillator to gener-
ate a Configuration Clock (CCLK) for driving potential slave
devices. They also generate address and timing for exter-
nal PROM(s) containing the configuration data.
Master Parallel (Up or Down) modes generate the CCLK
signal and PROM addresses and receive byte parallel
data. The data is internally serialized into the FPGA
data-frame format. The up and down selection generates
starting addresses at either zero or 3FFFF, for compatibility
with different microprocessor addressing conventions. The
Unrestricted User-Programmable I/O Pins
I/O
Weak
Pull-up
I/O
These pins can be configured to be input and/or output after configuration is completed.
Before configuration is completed, these pins have an internal high-value pull-up resis-
tor (20 k
- 100 k
) that defines the logic level as High.
Table 9: Pin Descriptions (Continued)
Pin Name
I/O
During
Config.
I/O
After
Config.
Pin Description
Table 10: Configuration Modes
Mode
M2
0
1
1
M1
0
1
0
M0
0
1
0
CCLK
output
input
output
Data
Bit-Serial
Bit-Serial
Byte-Wide,
increment
from 00000
Byte-Wide,
decrement
from 3FFFF
Byte-Wide
Master Serial
Slave Serial
Master
Parallel Up
Master
Parallel Down
1
1
0
output
Peripheral
Synchronous*
Peripheral
Asynchronous
Express
Reserved
0
1
1
input
1
0
1
output
Byte-Wide
0
0
1
0
0
1
input
—
Byte-Wide
—
相關PDF資料
PDF描述
XC5210-5PC84I Field Programmable Gate Array (FPGA)
XC5210-5PG223I Field Programmable Gate Array (FPGA)
XC5210-5PQ160I Field Programmable Gate Array (FPGA)
XC5210-5PQ208I Field Programmable Gate Array (FPGA)
XC5210-5PQ240I Field Programmable Gate Array (FPGA)
相關代理商/技術參數
參數描述
XC5210-4VQ100C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-4VQ64C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-5BG225C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-5BG225CO373 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Xilinx 功能描述:
XC5210-5BG352C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*