- 您現在的位置：買賣IC網 > PDF目錄19909 > XCF02SVO20C (Xilinx Inc)IC PROM IN SYST PRG 3.3V 20TSSOP PDF資料下載
參數資料
| 型號： | XCF02SVO20C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 13/35頁 |
| 文件大小： | 0K |
| 描述： | IC PROM IN SYST PRG 3.3V 20TSSOP |
| 標準包裝： | 74 |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 2Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Platform Flash In-System Programmable Configuration PROMs
DS123 (v2.18) May 19, 2010
Product Specification
20
R
THXT
EN_EXT_SEL hold time from CF, CE, or OE/RESET when VCCO = 3.3V or 2.5V
300
–
ns
EN_EXT_SEL hold time from CF, CE, or OE/RESET when VCCO = 1.8V
300
–
ns
TSRV
REV_SEL setup time to CF, CE, or OE/RESET when VCCO = 3.3V or 2.5V
300
–
ns
REV_SEL setup time to CF, CE, or OE/RESET when VCCO = 1.8V
300
–
ns
THRV
REV_SEL hold time from CF, CE, or OE/RESET when VCCO = 3.3V or 2.5V
300
–
ns
REV_SEL hold time from CF, CE, or OE/RESET when VCCO = 1.8V
300
–
ns
Notes:
1.
AC test load = 50 pF for XCF01S/XCF02S/XCF04S; 30 pF for XCF08P/XCF16P/XCF32P.
2.
Float delays are measured with 5 pF AC loads.Transition is measured at ±200 mV from steady-state active levels.
3.
Guaranteed by design, not tested.
4.
All AC parameters are measured with VIL = 0.0V and VIH = 3.0V.
5.
If THCE High < 2 s, TCE = 2 s.
6.
If THOE Low < 2 s, TOE = 2 s.
7.
This is the minimum possible TCYCO. Actual TCYCO = TCCDD + FPGA Data setup time. Example: With the XCF32P in serial mode with VCCO
at 3.3V, if FPGA Data setup time = 15 ns, then the actual TCYCO = 25 ns +15 ns = 40 ns.
8.
The delay before the enabled CLKOUT signal begins clocking data out of the device is dependent on the clocking configuration. The delay
before CLKOUT is enabled increases if decompression is enabled.
9.
Slower CLK frequency option might be required to meet the FPGA data sheet setup time.
10. When decompression is enabled, the CLKOUT signal becomes a controlled clock output. When decompressed data is available, CLKOUT
toggles at the source clock frequency (either the selected internal clock frequency or the external CLK input frequency). When
decompressed data is not available, the CLKOUT pin is parked High. If CLKOUT is used, then it must be pulled High externally using a
4.7 k
Ω pull-up to V
CCO.
11. When JTAG CONFIG command is issued, PROM drives CF Low for at least the THCF minimum.
Symbol
Description
XCF08P, XCF16P,
XCF32P
Units
Min
Max
相關PDF資料 |
PDF描述 |
|---|---|
| V24C28H100BL3 | CONVERTER MOD DC/DC 28V 100W |
| ACC25DRYH-S734 | CONN EDGECARD 50POS DIP .100 SLD |
| V24C28H100BL | CONVERTER MOD DC/DC 28V 100W |
| RBB106DHRT-S621 | CONN EDGECARD EXTEND 212POS .050 |
| V48C5H100B | CONVERTER MOD DC/DC 5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XCF02SVO20C0100 | 制造商:Xilinx 功能描述:IC SYSTEM GATE |
| XCF02SVO20C0936 | 制造商:Xilinx 功能描述:IC SYSTEM GATE |
| XCF02S-VO20CES | 制造商:Xilinx 功能描述: |
| XCF02SVO48 | 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMS |
| XCF02SVOG20C | 功能描述:IC PROM SRL FOR 2M GATE 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:- 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。