參數資料
型號： XR16C2850IM48
廠商： EXAR CORP
元件分類： 微控制器/微處理器
英文描述： 3.3V AND 5V DUART WITH 128-BYTE FIFO
中文描述： 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP48
封裝： 7 X 7 MM, 1 MM HEIGHT, TQFP-48
文件頁數： 12/43頁
文件大小： 611K
代理商： XR16C2850IM48
á
3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850
REV. 2.0.0
12
2.11 R
ECEIVER
The receiver section contains an 8-bit Receive Shift
Register (RSR) and 128 bytes of FIFO which includes
a byte-wide Receive Holding Register (RHR). The
RSR uses the 16X/8X clock (CLK8/16 pin) for timing.
It verifies and validates every bit on the incoming
character in the middle of each data bit. On the falling
edge of a start or false start bit, an internal receiver
counter starts counting at the 16X/8X clock rate. After
8 clocks (or 4 if 8X) the start bit period should be at
the center of the start bit. At this time the start bit is
sampled and if it is still a logic 0 it is validated. Evalu-
ating the start bit in this manner prevents the receiver
from assembling a false character. The rest of the da-
ta bits and stop bits are sampled and validated in this
same manner to prevent false framing. If there were
any error(s), they are reported in the LSR register bits
2-4. Upon unloading the receive data byte from RHR,
the receive FIFO pointer is bumped and the error tags
are immediately updated to reflect the status of the
data byte in RHR register. RHR can generate a re-
ceive data ready interrupt upon receiving a character
or delay until it reaches the FIFO trigger level. Fur-
thermore, data delivery to the host is guaranteed by a
receive data ready time-out interrupt when data is not
received for 4 word lengths as defined by LCR[1:0]
plus 12 bits time. This is equivalent to 3.7-4.6 charac-
ter times. The RHR interrupt is enabled by IER bit-0.
2.11.1 Receive Holding Register (RHR) - Read-
Only
The Receive Holding Register is an 8-bit register that
holds a receive data byte from the Receive Shift Reg-
ister. It provides the receive data interface to the host
processor. The RHR register is part of the receive
FIFO of 128 bytes by 11-bits wide, the 3 extra bits are
for the 3 error tags to be reported in LSR register.
When the FIFO is enabled by FCR bit-0, the RHR
contains the first data character received by the FIFO.
After the RHR is read, the next character byte is load-
ed into the RHR and the errors associated with the
current data byte are immediately updated in the LSR
bits 2-4.
F
IGURE
9. R
ECEIVER
O
PERATION
IN
NON
-FIFO M
ODE
Receive Data Shift
Register (RSR)
Receive
Data Byte
and Errors
RHR Interrupt (ISR bit-2)
Receive Data
Holding Register
(RHR)
RXFIFO1
16X or 8X
Clock
Receive Data Characters
Data Bit
Validation
Error
Tags in
LSR bits
4:2
相關PDF資料
PDF描述
XR16C2850IP40 3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850CJ DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
XR16C2850CM DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
XR16C2850CP DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
XR16C2850IJ DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
相關代理商/技術參數
參數描述
XR16C2850IM-F 功能描述:UART 接口集成電路 2.97V-5.5V 128B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C2850IMTR-F 制造商:Exar Corporation 功能描述:XR16C2850IMTR-F
XR16C2850IP 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
XR16C2850IP40 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2852 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*