- 您現在的位置：買賣IC網 > PDF目錄376453 > XR16C2850IM48 (EXAR CORP) 3.3V AND 5V DUART WITH 128-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16C2850IM48 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| 中文描述： | 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, TQFP-48 |
| 文件頁數： | 26/43頁 |
| 文件大?。?/td> | 611K |
| 代理商： | XR16C2850IM48 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
á
3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850
REV. 2.0.0
26
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indi-
cator. The THR bit is set to a logic 1 when the last da-
ta byte is transferred from the transmit holding regis-
ter to the transmit shift register. The bit is reset to log-
ic 0 concurrently with the data loading to the transmit
holding register by the host. In the FIFO mode this bit
is set when the transmit FIFO is empty, it is cleared
when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
This bit is set to a logic 1 whenever the transmitter
goes idle. It is set to logic 0 whenever either the THR
or TSR contains a data character. In the FIFO mode
this bit is set to a logic 1 whenever the transmit FIFO
and transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = A global indicator for the sum of all error
bits in the RX FIFO. At least one parity error, fram-
ing error or break indication is in the FIFO data.
This bit clears when there is no more error(s) in any
of the bytes in the RX FIFO.
4.9
M
ODEM
S
TATUS
R
EGISTER
(MSR) - R
EAD
O
NLY
This register provides the current state of the modem
interface input signals. Lower four bits of this register
are used to indicate the changed information. These
bits are set to a logic 1 whenever a signal from the
modem changes state. These bits may be used for
general purpose inputs when they are not used with
modem signals.
MSR[0]: Delta CTS# Input Flag
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since
the last time it was monitored. A modem status
interrupt will be generated if MSR interrupt is
enabled (IER bit-3).
MSR[1]: Delta DSR# Input Flag
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since
the last time it was monitored. A modem status
interrupt will be generated if MSR interrupt is
enabled (IER bit-3).
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0
to a logic 1, ending of the ringing signal. A modem
status interrupt will be generated if MSR interrupt is
enabled (IER bit-3).
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed
state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is
enabled (IER bit-3).
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow
control signal input if it is enabled and selected by Au-
to CTS (EFR bit-7). Auto CTS flow control allows
starting and stopping of local data transmissions
based on the modem CTS# signal. A logic 1 on the
CTS# pin will stop UART transmitter as soon as the
current character has finished transmission, and a
logic 0 will resume data transmission. Normally MSR
bit-4 bit is the compliment of the CTS# input. However
in the loopback mode, this bit is equivalent to the
RTS# bit in the MCR register. The CTS# input may be
used as a general purpose input when the modem in-
terface is not used.
MSR[5]: DSR Input Status
DSR#
(active high, logical 1). Normally this bit is the
compliment of the DSR# input. In the loopback mode,
this bit is equivalent to the DTR# bit in the MCR regis-
ter. The DSR# input may be used as a general pur-
pose input when the modem interface is not used.
MSR[6]: RI Input Status
RI# (active high, logical 1). Normally this bit is the
compliment of the RI# input. In the loopback mode
this bit is equivalent to bit-2 in the MCR register. The
RI# input may be used as a general purpose input
when the modem interface is not used.
MSR[7]: CD Input Status
CD# (active high, logical 1). Normally this bit is the
compliment of the CD# input. In the loopback mode
this bit is equivalent to bit-3 in the MCR register. The
CD# input may be used as a general purpose input
when the modem interface is not used.
4.10 S
CRATCH
P
AD
R
EGISTER
(SPR) - R
EAD
/W
RITE
This is a 8-bit general purpose register for the user to
store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (de-
fault) after a reset or a power off-on cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C2850IP40 | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2850CJ | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850CM | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850CP | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IJ | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2850IM-F | 功能描述:UART 接口集成電路 2.97V-5.5V 128B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2850IMTR-F | 制造商:Exar Corporation 功能描述:XR16C2850IMTR-F |
| XR16C2850IP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IP40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2852 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS |
發布緊急采購，3分鐘左右您將得到回復。