- 您現在的位置：買賣IC網 > PDF目錄1974 > XR16C2852IJ-F (Exar Corporation)IC UART FIFO 128B 44PLCC PDF資料下載
參數資料
| 型號： | XR16C2852IJ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 22/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 128B 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 其它名稱： | 1016-1659 XR16C2852IJ-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
xr
XR16C2852
REV. 2.1.1
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
29
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to a logical 0 for the transmit and receive
data.
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, LOW, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Alternate Function Register (AFR) - Read/Write
This register is used to select specific modes of MF# operation and to allow both UART register sets to be
written concurrently.
AFR[0]: Concurrent Write Mode
When this bit is set, the CPU can write concurrently to the same register in both UARTs. This function is
intended to reduce the dual UART initialization time. It can be used by the CPU when both channels are
initialized to the same state. The external CPU can set or clear this bit by accessing either register set. When
this bit is set, the channel select pin still selects the channel to be accessed during read operations. The user
should ensure that LCR Bit-7 of both channels are in the same state before executing a concurrent write to the
registers at address 0, 1, or 2.
Logic 0 = No concurrent write (default).
Logic 1 = Register set A and B are written concurrently with a single external CPU I/O write operation.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, “1”
1
Forced parity to space, “0”
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C850IMTR-F | IC UART FIFO 128B 48TQFP |
| XR16C854IQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR16C864IQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR16L2450IJ-F | IC UART FIFO 1B DUAL 44PLCC |
| XR16L2550IJ-F | IC UART FIFO 16B DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2852IJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR-16C450CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
| XR-16C450CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
| XR-16C452CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
| XR-16C550CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
發布緊急采購，3分鐘左右您將得到回復。