- 您現在的位置：買賣IC網 > PDF目錄376453 > XR16C854CQ (EXAR CORP) QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16C854CQ |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| 中文描述： | 4 CHANNEL(S), 2M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, PLASTIC, QFP-100 |
| 文件頁數： | 30/51頁 |
| 文件大?。?/td> | 476K |
| 代理商： | XR16C854CQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16C854
30
Rev. 1.00P
LCR BIT-3:
Parity or no parity can be selected via this bit.
Logic 0 = No parity. (normal default condition)
Logic 1 = A parity bit is generated during the transmis-
sion, receiver checks the data and parity for transmis-
sion errors.
LCR BIT-4:
If the parity bit is enabled with LCR bit-3 set to a logic
1, LCR BIT-4 selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd
number of logic 1s in the transmitted data. The
receiver must be programmed to check the same
format. (normal default condition)
Logic 1 = EVEN Parity
is generated by forcing an even
the number of logic 1s in the transmitted. The receiver
must be programmed to check the same format.
LCR BIT-5:
If the parity bit is enabled, LCR BIT-5 selects the
forced parity format.
LCR BIT-5 = logic 0, parity is not forced. (normal
default condition)
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit
is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit
is forced to a logical 0 for the transmit and receive
data.
LCR
Bit-5
LCR
Bit-4
LCR
Bit-3
Parity selection
X
0
0
1
1
X
0
1
0
1
0
1
1
1
1
No parity
Odd parity
Even parity
Force parity 1
Forced parity 0
LCR BIT-6:
When enabled the Break control bit causes a break
condition to be transmitted (the TX output is forced to
a logic 0 state). This condition exists until disabled by
setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (normal default
condition)
Logic 1 = Forces the transmitter output (TX) to a logic
0 for alerting the remote receiver to a line break
condition.
LCR BIT-7:
The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled. (normal default
condition)
Logic 1 = Divisor latch and enhanced feature register
enabled.
Modem Control Register (MCR)
This register controls the interface with the modem or
a peripheral device.
MCR BIT-0:
Logic 0 = Force -DTR output to a logic 1. (normal
default condition)
Logic 1 = Force -DTR output to a logic 0.
MCR BIT-1:
Logic 0 = Force -RTS output to a logic 1. (normal
default condition)
Logic 1 = Force -RTS output to a logic 0.
Automatic RTS may be used for hardware flow control
by enabling EFR bit-6 (See EFR bit-6).
MCR BIT-2:
This bit is used in the Loop-back mode only. In the
loop-back mode this bit is use to write the state of the
modem -RI interface signal via -OP1.
MCR BIT-3: (
Used to control the modem -CD signal
in the loop-back mode.)
Logic 0 = Forces INT (A-D) outputs to the three state
mode during the 16 mode. (normal default condition)
In the Loop-back mode, sets -OP2 (-CD) internally to
a logic 1.
Logic 1 = Forces the INT (A-D) outputs to the active
mode during the 16 mode. In the Loop-back mode,
sets -OP2 (-CD) internally to a logic 0.
MCR BIT-4:
Logic 0 = Disable loop-back mode. (normal default
condition)
Logic 1 = Enable local loop-back mode (diagnostics).
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C854CV | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| XR16C854DCV | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| XR16C854DIV | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| XR16C854IJ | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| XR16C854IQ | QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C854CQ-0A-EVB | 功能描述:UART 接口集成電路 Supports C854 100 ld QFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C854CQ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C854CQTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C854CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UART WITH RX/TX FIFO COUNTERS,128-BYTE FIFO |
| XR16C854CV-0A-EVB | 功能描述:UART 接口集成電路 Supports C854 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。