- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L2751IM (EXAR CORP) 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE PDF資料下載
參數資料
| 型號： | XR16L2751IM |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE |
| 中文描述： | 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, TQFP-48 |
| 文件頁數： | 4/52頁 |
| 文件大小： | 618K |
| 代理商： | XR16L2751IM |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
á
XR16L2751
2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
REV. 1.0.0
4
RXRDYA#
31
O
UART channel A Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel A.
TXRDYB#
6
O
UART channel B Transmitter Ready (active low). The output provides the TX FIFO/
THR status for transmit channel B.
RXRDYB#
18
O
UART channel B Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel B.
MODEM OR SERIAL I/O INTERFACE
TXA
7
O
UART channel A Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be a
logic 1 during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is a logic 0. If it is not used, leave it unconnected.
RXA
5
I
UART channel A Receive Data or infrared receive data. Normal receive data input
must idle at logic 1 condition. The infrared receiver pulses typically idles at logic 0 but
can be inverted by software control prior going to the decoder, see MCR[6] and
FCTR[2].
RTSA#
33
O
UART channel A Request-to-Send (active low) or general purpose output. This out-
put must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see
FCTR[3] and EMSR[3].
CTSA#
38
I
UART channel A Clear-to-Send (active low) or general purpose input. It can be used
for auto CTS flow control, see EFR[7], MSR[4] and IER[7]. This input should be con-
nected to VCC when not used.
DTRA#
34
O
UART channel A Data-Terminal-Ready (active low) or general purpose output.
DSRA#
39
I
UART channel A Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
CDA#
40
I
UART channel A Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
RIA#
41
I
UART channel A Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
OP2A#
32
O
Output Port 2 Channel A - The output state is defined by the user and through the
software setting of MCR[3]. When MCR[3] is set to a logic 1, INTA is set to the level
mode and OP2A# output to a logic 0. When MCR[3] is set to a logic 0, INTA is set to
the three state mode and OP2A# to a logic 1. See MCR[3]. This output must not be
used as a general output when the interrupt output is used else it will disturb the INTA
output functionality.
TXB
8
O
UART channel B Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be a
logic 1 during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is a logic 0. If it is not used, leave it unconnected.
Pin Description
N
AME
48-TQFP
P
IN
#
T
YPE
D
ESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2752 | 2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752CJ | 2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752IJ | 2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L580 | SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L580IL | SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2751IM-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2751IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L2751IMTR-F |
| XR16L2752 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752CJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752CJ-0A-EB | 功能描述:UART 接口集成電路 Supports L2750 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。