- 您現在的位置：買賣IC網 > PDF目錄16498 > XR16V554IJ-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16V554 68PLCC PDF資料下載
參數資料
| 型號： | XR16V554IJ-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 16/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V554 68PLCC |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
XR16V554/554D
23
REV. 1.0.3
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the
DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY and RXRDY pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR BIT-7
FCR BIT-6
RECEIVE TRIGGER LEVEL
0
1
0
1
0
1
4
8
14
相關PDF資料 |
PDF描述 |
|---|---|
| 6374109-5 | C/A 62.5/125 1.6MM LC 5M |
| LB2012T100M | INDUCTOR WOUND 10UH 120MA 0805 |
| M3DRK-1020K | IDC CABLE - MKR10K/MC10F/MPR10K |
| VI-JN1-EZ-S | CONVERTER MOD DC/DC 12V 25W |
| EEC15DRXI-S734 | CONN EDGECARD 30POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V554IJ-F | 功能描述:UART 接口集成電路 2.25V-3.6V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V554IJTR-F | 功能描述:UART 接口集成電路 XR16V554IJTR-F RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V554IL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V554IL-0A-EVB | 功能描述:UART 接口集成電路 Supports V554 48 pin QFN,ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V554IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。