- 您現在的位置：買賣IC網 > PDF目錄16433 > XR16V598IQ-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16V598-A 100QFP PDF資料下載
參數資料
| 型號： | XR16V598IQ-0B-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 29/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V598-A 100QFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
XR16V598
35
REV. 1.0.3
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO
]
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
ISR[5:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 13). See “Section
and “Section 4.4.2, Interrupt Clearing:” on page 34 for details.
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending. (default condition)
4.5
FIFO Control Register (FCR) - Write Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 14 shows the complete selections.
Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last
applies to both the RX and TX side.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO interrupt. The UART will issue a transmit interrupt when
the number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that
the FIFO did not get filled over the trigger level on last re-load. Table 14 below shows the selections.
TABLE 13: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF THE INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Received Data Ready)
3
0
1
0
RXRDY (Receive Data Time-out)
4
0
1
0
TXRDY (Transmitter Holding Register Empty)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xon/Xoff or Special character)
7
1
0
CTS#/DSR#, RTS#/DTR# change of state
X
0
1
None (default) or wake-up indicator
相關PDF資料 |
PDF描述 |
|---|---|
| CM322522-820KL | INDUCTOR 82UH 60MA SMD |
| VI-2V2-EX | CONVERTER MOD DC/DC 15V 75W |
| XR16V598IQ-0A-EVB | EVAL BOARD FOR XR16V598-A 100QFP |
| APX809-46SRG-7 | IC MPU RESET CIRC 4.63V SOT23R-3 |
| 176819-000 | SOLDERSLEEVE LO-FIRE 11.5MM DIA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V598IQ100 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16V598IQ100-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V654 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654_0709 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654D | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。