- 您現在的位置：買賣IC網 > PDF目錄16433 > XR16V598IQ-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16V598-A 100QFP PDF資料下載
參數資料
| 型號： | XR16V598IQ-0B-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 57/58頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16V598-A 100QFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁
XR16V598
8
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO
REV. 1.0.3
2.4
INT# Ouput
The INT# interrupt output changes according to the operating mode and enhanced features setup. Table 2
and 3 summarize the operating behavior for the transmitter and receiver.
2.5
Crystal Oscillator
The 598 includes an on-chip oscillator. The crystal oscillator provides the system clock to the Baud Rate
Generators (BRG) in each of the 8 UARTs, the 16-bit general purpose timer/counter and internal logics. XTAL1
is the input to the oscillator or external clock buffer input with XTAL2 pin being the output. For programming
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 3). Alternatively, an external
clock can be connected to the XTAL1 pin to clock the internal 8 baud rate generators for standard or custom
rates. The typical oscillator connections are shown in Figure 3. For further reading on oscillator circuit please
see application note DAN108 on EXAR’s web site.
TABLE 2: INT# PIN OPERATION FOR TRANSMITTER
Auto RS485
Mode
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
NO
HIGH = a byte in THR
LOW = THR empty
HIGH = FIFO above trigger level
LOW = FIFO below trigger level or FIFO empty
YES
HIGH = a byte in THR
LOW = transmitter empty
HIGH = FIFO above trigger level
LOW = FIFO below trigger level or transmitter empty
TABLE 3: INT# PIN OPERATION FOR RECEIVER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
HIGH = no data
LOW = 1 byte
HIGH = FIFO below trigger level
LOW = FIFO above trigger level
FIGURE 3. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47pF
C2
22-47pF
24 MHz
XTAL1
XTAL2
R=300K to 400K
相關PDF資料 |
PDF描述 |
|---|---|
| CM322522-820KL | INDUCTOR 82UH 60MA SMD |
| VI-2V2-EX | CONVERTER MOD DC/DC 15V 75W |
| XR16V598IQ-0A-EVB | EVAL BOARD FOR XR16V598-A 100QFP |
| APX809-46SRG-7 | IC MPU RESET CIRC 4.63V SOT23R-3 |
| 176819-000 | SOLDERSLEEVE LO-FIRE 11.5MM DIA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V598IQ100 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16V598IQ100-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V654 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654_0709 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654D | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。