- 您現在的位置：買賣IC網 > PDF目錄376455 > XR17D158 (Exar Corporation) UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART PDF資料下載
參數資料
| 型號： | XR17D158 |
| 廠商： | Exar Corporation |
| 英文描述： | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| 中文描述： | 通用（3.3V和5V）PCI總線八進制的UART |
| 文件頁數： | 47/72頁 |
| 文件大?。?/td> | 1520K |
| 代理商： | XR17D158 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
xr
REV. 1.2.1
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
XR17D158
47
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (for 16C550 compatibility) (default).
Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[6]: Infrared Encoder/Decoder Enable
The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware
reset or a soft-reset. Afterward user can override this bit for desired operation.
Logic 0 = Disable the infrared mode, operates in the normal serial character mode.
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this mode the infrared TX output will be a logic 0 during idle
data conditions. FCTR bit-4 may be selected to invert the RX input signal level going to the decoder for
infrared modules that provide rather an inverted output.
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one-fourth.
5.8.9
Line Status Register (LSR) - Read/Only
This register provides the status of data transfers between the UART and the host. If IER bit-2 is set to a logic
1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break). Reading LSR will clear LSR bits 4-1.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error. This bit is cleared after LSR is read.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR. This bit is cleared after LSR is read.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR. This bit is cleared after LSR is read.
LSR[4]: Receive Break Tag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was a logic 0 for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. This bit is cleared after LSR is read.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17D158CV | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17L152IM | CAP .068UF 400V PEN FILM 2825 5% |
| XR17L152 | 3.3V PCI BUS DUAL UART |
| XR17L152CM | 3.3V PCI BUS DUAL UART |
| XR2001 | High-Voltage, High-Current Darlington Transistor Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17D158_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17D158CV | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D158CV-0A-EVB | 功能描述:界面開發工具 Supports D158 144 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17D158CV-F | 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D158CV-F-SIWI | 制造商:Exar Corporation 功能描述:FOR WILLIAMS GAMING THEIR CM'S 制造商:EXAR 功能描述:XR17D158CV-F-SIWI 制造商:EXAR 功能描述:FOR WILLIAMS GAMING THEIR CM'S |
發布緊急采購，3分鐘左右您將得到回復。