- 您現在的位置：買賣IC網 > PDF目錄16821 > XR17V358IB-E4-EVB (Exar Corporation)EVAL BOARD FOR XR17V358-E4 PDF資料下載
參數資料
| 型號： | XR17V358IB-E4-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 52/68頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR17V358-E4 |
| 產品培訓模塊： | PCIe UARTs UART Product Overview |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR17V358 |
| 已供物品： | 板 |
| 相關產品： | 1016-1294-ND - IC UART PCIE OCTAL 176FPBGA |
| 其它名稱： | 1016-1295 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
XR17V358
56
HIGH PERFORMANCE OCTAL PCI EXPRESS UART
REV. 1.0.4
MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode)
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit [6]. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR
register, as shown in Figure 12.
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit [6] and MCR bit [2]=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a HIGH (default).
Logic 1= Force RTS# output to LOW.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit [6] and MCR bit [2]=1. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a HIGH (default).
Logic 1 = Force DTR# output to a LOW.
4.9
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit [2] is set to a
logic 1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break).
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO.
LSR[6]: Transmitter Empty Flag
This bit is the Transmitter Empty indicator. This bit is set to a logic 1 whenever both the transmit FIFO (or THR,
in non-FIFO mode) and the transmit shift register (TSR) are both empty. It is set to logic 0 whenever either the
TX FIFO or TSR contains a data character.
LSR[5]: Transmit FIFO Empty Flag
This bit is the Transmit FIFO Empty indicator. This bit indicates that the transmitter is ready to accept a new
character for transmission. This bit is set to a logic HIGH when the last data byte is transferred from the
transmit FIFO to the transmit shift register. The bit is reset to logic 0 as soon as a data byte is loaded into the
transmit FIFO. In the non-FIFO mode this bit is set when the transmit holding register (THR) is empty; it is
cleared when at a byte is written to the THR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input
returns to the idle condition, “mark” or HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| ECA10DTKT-S288 | CONN EDGECARD 20POS .125 EXTEND |
| H0PPS-2406G | DIP CABLE - HDP24S/AE24G/HDP24S |
| EBM25DRMH | CONN EDGECARD 50POS .156 WW |
| HCM08DSEI-S243 | CONN EDGECARD 16POS .156 EYELET |
| HMM06DRYH-S13 | CONN EDGECARD 12POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V358IB-E8-EVB | 功能描述:界面開發工具 Eval Board for XR17V358IB-E8 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR1857SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1858SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1859SN | 制造商:Electro-Term/Hollingsworth 功能描述: |
| XR1859SNT | 制造商:Hollingsworth 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。