- 您現在的位置：買賣IC網 > PDF目錄3766 > XR20M1172IL32-F (Exar Corporation)IC UART FIFO I2C/SPI 64B 32QFN PDF資料下載
參數資料
| 型號： | XR20M1172IL32-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 13/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO I2C/SPI 64B 32QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1477 XR20M1172IL32-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XR20M1172
20
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
REV. 1.2.0
2.12
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 15), the M1172 compares one or two sequential receive
data characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the M1172 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the M1172 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the M1172 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the M1172 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the M1172 automatically
sends the Xoff-1,2 via the serial TX output to the remote modem when the RX FIFO reaches the Halt Level
(TCR[3:0]). To clear this condition, the M1172 will transmit the programmed Xon-1,2 characters as soon as RX
FIFO falls down to the Resume Level.
2.13
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The M1172 compares each incoming receive character with Xoff-2 data. If a match exists, the received data
will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the
Internal Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison.
2.14
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by EFCR
bit-4. It also changes the behavior of the transmit empty interrupt (see Table 4). When idle, the auto RS485
half-duplex direction control signal (RTS#) is HIGH for receive mode. When data is loaded into the THR for
transmission, the RTS# output is automatically asserted LOW prior to sending the data. After the last stop bit of
the last character that has been transmitted, the RTS# signal is automatically de-asserted. This helps in turning
around the transceiver to receive the remote station’s response. When the host is ready to transmit next polling
data packet, it only has to load data bytes to the transmit FIFO. The transmitter automatically re-asserts RTS#
(LOW) output prior to sending the data. The polarity of the RTS# output pin can be inverted by setting EFCR[5]
= 1.
2.14.1
Normal Multidrop Mode
Normal multidrop mode is enabled when EFCR bit-0 = 1 and EFR bit-5 = 0 (Special Character Detect
disabled). The receiver is set to Force Parity 0 (LCR[5:3] = ’111’) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an address byte is received
(parity bit = 1). This address byte will cause the UART to set the parity error. The UART will generate an LSR
interrupt and place the address byte in the RX FIFO. The software then examines the byte and enables the
receiver if the address matches its slave address, otherwise, it does not enable the receiver.
If the receiver has been enabled, the receiver will receive the subsequent data. If an address byte is received,
it will generate an LSR interrupt. The software again examines the byte and If the address matches its slave
addres, it does not have to anything. If the address does not match its slave address, then the receiver should
be disabled.
相關PDF資料 |
PDF描述 |
|---|---|
| XR88C192CV-F | IC UART FIFO DUAL 44LQFP |
| XR16L2550IM-F | IC UART FIFO 16B DUAL 48TQFP |
| XR21V1412IL32-F | IC UART FIFO USB DUAL 32QFN |
| ST16C650ACQ48-F | IC UART FIFO 32B 48TQFP |
| XR68M752IM48-F | IC UART FIFO 64B DUAL 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20M1172IL32-F | 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 32-QFN |
| XR20M1172L32-0A-EB | 功能描述:UART 接口集成電路 Supports M1172 32pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1172L32-0B-EB | 功能描述:UART 接口集成電路 Supports M1172 32pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1280 | 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS |
| XR20M1280IL24-F | 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。