- 您現在的位置：買賣IC網 > PDF目錄3762 > XR88C681CJTR-F (Exar Corporation)IC UART CMOS DUAL 44PLCC PDF資料下載
參數資料
| 型號： | XR88C681CJTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 7/101頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART CMOS DUAL 44PLCC |
| 標準包裝： | 500 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 1 字節，3 字節 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | XR88C681CJTR-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
XR88C681
13
Rev. 2.11
SYSTEM DESCRIPTION
The XR88C681 consists of two independent, full-duplex
communication channels; each consisting of their own
Transmitter and Receiver. Each channel of the DUART
may be independently programmed for operating mode
and data format. The DUART can interface to a wide
range of processors with a minimal amount of
components. The operating speed of each receiver and
transmitter may be selected from one of 23 internally
generated fixed bit rates, from a clock derived from an
internal counter/timer, or from an externally supplied 1x or
16x clock. The bit rate generator (the source of the 23
different fixed bit rates) can operate directly from a crystal
connected across two pins or from an external clock. The
ability to independently program the operating speed of
the receiver and transmitter of each channel makes the
DUART attractive for split speed channel applications
such as clustered terminal systems.
Receiver data is quadrupled buffered and the transmitter
data is dual-buffered via on-chip FIFOs in order to
minimize the risk of receiver overrun and to reduce
overhead in interrupt driven applications. The DUART
also provides a flow control capability to inhibit
transmission from a remote device when the buffer of the
receiving DUART is full, thus preventing loss of data.
The DUART also provides a general purpose 16 bit
counter/timer (which may also be used as programmable
bit rate generators), a 7 bit multi-purpose input port and an
8 bit multi-purpose output port (for the 40 pin DIP and 44
pin PLCC packages only).
PRINCIPLES OF OPERATION
Figure 1 presents an overall block diagram of the DUART.
As illustrated in the block diagram, the DUART consists of
the following major functional blocks:
D
Data Bus Buffer
D
Interrupt Control
D
Input Port
D
Serial Communication Channels A and B
D
Operation Control
D
Timing Control
D
Output Port
A. DATA BUS BUFFER
The data bus buffer provides the interface between the
internal (within the chip) and external data buses. It is
controlled by the operation control block to allow data
transfers to take place between the host CPU and the
DUART.
B. OPERATION CONTROL BLOCK
The control logic of the Operation Control block receives
operating commands from the CPU and generates proper
signals to the various sections of the DUART. The
Operation Control Block functions as the user interface to
the rest of the device. Specifically, it is responsible for
DUART Register Address Decoding, and Command
Decoding. Therefore all commands to set baud rates,
parity, other communication protocol parameters, start or
stop the Counter/Timer or reading a “status register” to
monitor data communication performance must go
through the Operation Control Block.
The Operation Control Block will control DUART
performance based upon the following input signals.
Address Inputs, A0 - A3
-RD
-WR
-CS
RESET
When using the 6800 family processor, the DUART will
require some glue logic. Interfacing a 6800 Family
Processor to the DUART can be easily achieved by
including a small amount of external logic devices, as
depicted in
Figure 2.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C2550IQ48TR-F | IC UART FIFO 16B DUAL 48TQFP |
| XR16C2550IMTR-F | IC UART FIFO 16B DUAL 48TQFP |
| ST78C34CP40-F | IC UART FIFO 83B 40PDIP |
| XR16M2551IL32TR-F | IC UART FIFO 16B DUAL 32QFN |
| XR16L2551ILTR-F | IC UART FIFO 16B DUAL 32QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C681CN/40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR88C681CP/28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR88C681CP/28-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C681CP/40 | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C681CP/40-F | 功能描述:UART 接口集成電路 0.5V-2V UART temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。