參數資料
型號： XRT71D00
廠商： Exar Corporation
英文描述： E3/DS3/STS-1 JITTER ATTENUATOR,STS-1 TO DS3 DESYNCHRONIZER
中文描述： E3/DS3/STS-1抖動衰減器，STS - 1的到DS3 DESYNCHRONIZER
文件頁數： 4/22頁
文件大?。?/td> 254K
代理商： XRT71D00
XRT71D03
3 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR, STS-1 TO DS3 DESYNCHRONIZER
REV. 1.1.0
á
2
PIN DESCRIPTIONS
PIN DESCRIPTION
P
IN
#
N
AME
T
YPE
D
ESCRIPTION
1
AVDD
****
Analog Power Supply = 5V±5% or 3.3V±5%
2
GND
****
Digital Power Supply = 5V±5% or 3.3V±5%
3
RRCLK_0
O
Received Recovered Output (De-jittered) Clock - channel 0:
Output the de-jittered or smoothed clock if the jitter attenuator is enabled. The
de-jittered data, RRPOS/RRNEG are clocked to this signal.
If RRCLKES is “l(fā)ow”, RRPOS/RRNEG will be updated at the falling edge of
RRCLK.
If RRCLKES is “high”, RRPOS/RRNEG will be updated at the rising edge of
RRCLK.
4
RRPOS_0
O
Received Recovered Positive Data (De-Jittered) Output - channel
0:
De-jittered positive data output. Updated on the rising or falling edge of
RRCLK, depending upon the state of the RRCLKES input pin (or bit-field set-
ting).
5
RRNEG_0
O
Received Recovered Negative Data (De-Jittered) Output - channel
0:
De-jittered negative data output. Updated on the rising or falling edge of
RRCLK, depending upon the state of the RRCLKES input pin (or bit-field set-
ting).
6
RRCLKES
I
Received Recovered Clock Edge Select Input:
Hardware Mode:
1. When RRCLKES = “0”, then RRPOS and RRNEG are updated on the fall-
ing edge of RRCLK
2. When RRCLKES = “1”, then RRPOS and RRNEG are updated on the rising
edge of RRCLK
N
OTE
:
This applies to all channels.
Host Mode
Connect this pin to GND when the 71D03 is configured in the Host Mode.
Internal 50 K Ohm pull-down resistor.
7
NC
No Connection
8
Rest
I
Reset Input.
(Active-Low):
A high-low transition will re-center the internal FIFO, and will clear the Com-
mand Registers (for Host Mode operation). Resetting this pin may corrupt data
within the device.
For normal operation, pull this pin to VDD.
Internal 50 K Ohm pull-up resistor.
9
DS3/E3_1
I
DS3/E3 Select Input - channel 1
:
This pin along with the STS-1 mode select pin selects the operating mode. The
following table provides the configuration:
STS-1
DS3/E3
XRT71D04 Operating Mode
0 0 DS3 (44.736 MHz)
0 1 E3 (34.368 MHz)
1 0 STS-1 (51.84 MHz)
1 1 E3 (34.368 MHz)
Internal 50 K Ohm pull-down resistor.
10
VDD
****
Digital Power Supply = 5V±5% or 3.3V±5%
相關PDF資料
PDF描述
XRT71D00IQ E3/DS3/STS-1 JITTER ATTENUATOR,STS-1 TO DS3 DESYNCHRONIZER
XRT71D04IV 4 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR, STS-1 TO DS3 DESYNCHRONIZER
XRT7298IP PCM Transmitter
XRT7298IW PCM Transmitter
XRT72L71IQ Telecommunication IC
相關代理商/技術參數
參數描述
XRT71D00_01 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 JITTER ATTENUATOR
XRT71D00ES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT71D00ES-L00 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT71D00IQ 功能描述:時鐘合成器/抖動清除器 T3/E3 Jitter Attenuator RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT71D00IQ-F 功能描述:時鐘合成器/抖動清除器 DS3/E3/STS-1Jit Attn 3.3/5.0V 1 CH 1 CHIP RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*