參數資料
型號: XRT73LC00AIV-F
廠商: Exar Corporation
文件頁數: 22/61頁
文件大小: 0K
描述: IC LIU STS1/DS3/E3 SGL 44TQFP
標準包裝: 160
類型: 線路接口裝置(LIU)
驅動器/接收器數: 1/1
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 44-LQFP
供應商設備封裝: 44-TQFP(10x10)
包裝: 托盤
XRT73LC00A
26
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT
B. access the Microprocessor Serial Interface and write a “1” into the TXBIN (TRANSMIT BINary) bit-field in
Command Register 1.
After taking these steps, the Transmit Logic Block accepts Single-Rail data via the TPDATA input pin. The
XRT73LC00A samples this input pin on the falling edge of the TCLK clock signal and encodes it into the
appropriate bipolar line signal across the TTIP and TRING output pins.
NOTES:
1.
In this mode the Transmit Logic Block ignores the TNDATA input pin.
2.
If the Transmit Section of the XRT73LC00A is configured to accept Single-Rail data from the Terminal Equipment,
the B3ZS/HDB3 Encoder must be enabled.
Figure 13 illustrates the behavior of the TPDATA and TCLK signals when the Transmit Logic Block has been
configured to accept Single-Rail data from the Terminal Equipment.
2.2
The Transmit Clock Duty Cycle Adjust Circuitry
The on-chip Pulse-Shaping circuitry in the Transmit Section of the XRT73LC00A has the responsibility for
generating pulses of the shape and width to comply with the applicable pulse template requirement. The
widths of these output pulses are defined by the width of the half-period pulses in the TCLK signal.
Allowing the widths of the pulses in the TCLK clock signal to vary significantly could jeopardize the chip’s ability
to generate Transmit Output pulses of the appropriate width, thereby failing the applicable Pulse Template
Requirement Specification. The chips ability to generate compliant pulses could depend upon the duty cycle of
the clock signal applied to the TCLK input pin.
In order to combat this phenomenon, the Transmit Clock Duty Cycle Adjust circuit was designed into the
XRT73LC00A. The Transmit Clock Duty Cycle Adjust Circuitry is a PLL that was designed to accept clock
pulses via the TCLK input pin at duty cycles ranging from 30% to 70% and to regenerate these signals with a
50% duty cycle.
The XRT73LC00A Transmit Clock Duty Cycle Adjust circuit alleviates the need to supply a signal with a 50%
duty cycle to the TCLK input pin.
2.3
The HDB3/B3ZS Encoder Block
The purpose of the HDB3/B3ZS Encoder Block is to aid in the Clock Recovery process at the Remote Terminal
Equipment by ensuring an upper limit on the number of consecutive zeros that can exist in the line signal.
2.3.1
B3ZS Encoding
If the XRT73LC00A is configured to operate in the DS3 or SONET STS-1 Modes, then the HDB3/B3ZS
Encoder block operates in the B3ZS Mode. When the Encoder is operating in this mode, it parses through and
COMMAND REGISTER CR1 (ADDRESS = 0X01)
D4
D3
D2
D1
D0
TXOFF
TAOS
TXCLKINV
TXLEV
TXBIN
X
1
FIGURE 13. THE BEHAVIOR OF THE TPDATA AND TCLK INPUT SIGNALS WHILE THE TRANSMIT LOGIC BLOCK IS
ACCEPTING SINGLE-RAIL DATA FROM THE TERMINAL EQUIPMENT
TCLK
TPDATA
Data
1
0
相關PDF資料
PDF描述
XRT73LC03AIV-F IC LIU E3/DS3/STS-1 3CH 120LQFP
XRT73LC04AIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
XRT73R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75L00DIV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
相關代理商/技術參數
參數描述
XRT73LC00AIVTR 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73LC00AIVTR-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73LC00IV 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73LC03A 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC03A_08 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT