參數資料
型號： XRT73LC03AIV
廠商： Exar Corporation
文件頁數： 33/61頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 3CH 120LQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 3/3
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 120-LQFP
供應商設備封裝： 120-LQFP（14x20）
包裝： 托盤
XRT73LC03A
37
REV. 1.0.4
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
When the System Manufacturer is interfacing the Re-
ceive Section of the XRT73LC03A to the Cross-Con-
nect, they should be aware of the following facts:
1. All DS3 or STS-1 line signals that are present at
either the DSX-3 or the STSX-1 Cross Connect
are required to meet the Isolated Pulse Template
Requirements per Bellcore GR-499-CORE for
DS3 applications, or Bellcore GR-253-CORE for
STS-1 applications.
2. Bellcore documents state that the amplitude of
these pulses at the DSX-3 or STSX-1 location
can range in amplitude from 360mVpk to
850mVpk.
3. Bellcore documents stipulate that the Receiving
Terminal must be able to receive the pulse tem-
plate compliant line signal over a cable length of
0 to 450 feet from the DSX-3 or the STSX-1
Cross-Connect location.
These facts are reflected in Figure 23.
Design Considerations for DS3 and STS-1 Appli-
cations
When installing equipment into environments depict-
ed in Figure 23, the system installation personnel
may be able to determine the cable length between
the local terminal equipment and the DSX-3/STSX-1
Cross-Connect Patch-Panel. The cable length be-
tween the local terminal equipment and the DSX-3/
STSX-1 Cross-Connect Patch Panel ranges between
0 and 450 feet.
It is extremely unlikely that the system installation
personnel will know the cable length between the
DSX-3/STSX-1 Cross-Connect Patch-Panel and the
remote terminal equipment. Therefore, we recom-
mend that the Receive Equalizer be enabled by set-
ting the REQEN_(n) input pin or bit-field to “1”.
The only time that the Receive Equalizer should be
disabled is when there is an off-chip equalizer in the
Receive path between the DSX-3/STSX-1 Cross-
Connect and the RTIP_(n)/RRING_(n) input pins, or
in applications where the Receiver is directly monitor-
ing the transmit output signal directly.
3.2.1.2
Design Considerations for E3 Applica-
tions
In E3 System installation, it is recommended that the
Receive Equalizer of the XRT73LC03A device be en-
abled by pulling the REQEN_(n) input pins “High” or
by setting the REQEN_(n) bit-fields to “1”.
NOTE: The results of extensive testing indicates that when
the Receive Equalizer is enabled, the XRT73LC03A device
is capable of receiving an E3 line signal with anywhere from
0 to 12dB of cable loss over the Industrial Temperature
range.
Design Considerations for E3 Applications or if
the Overall Cable Length is known
If during System Installation the overall cable length
is known, then in order to optimize the performance
of the XRT73LC03A in terms of receive intrinsic jitter,
etc., enable or disable the Receive Equalizer based
upon the following recommendations:
The Receive Equalizer should be turned ON if the
Receive Section of a given channel is going to re-
ceive a line signal with an overall cable length of 300
feet or greater. Conversely, turn OFF the Receive
Equalizer if the Receive Section of a given channel is
going to receive a line signal over a cable length of
less than 300 feet.
NOTES:
1. If the Receive Equalizer block is turned ON when it
is receiving a line signal over short cable length,
the received line signal may be over-equalized
which could degrade performance by increasing
the amount of jitter that exists in the recovered data
and clock signals or by creating bit-errors
2. The Receive Equalizer has been designed to
counter the frequency-dependent cable loss that a
line signal experiences as it travels from the trans-
mitting terminal to the receiving terminal. However,
the Receive Equalizer was not designed to counter
flat loss where all of the Fourier frequency compo-
nents within the line signal are subject to the same
amount of attenuation. Flat loss is handled by the
AGC block.
Disable the Receive Equalizer block by doing either
of the following.
a. Operating in the Hardware Mode
Set the REQEN_(n) input pin “Low".
b. Operating in the HOST Mode
Write a "0" to the REQEN_(n) bit-field within Com-
mand Register CR2, as illustrated below.
COMMAND REGISTER CR2-(n)
D4
D3
D2
D1
D0
Reserved
ENDECDIS_(n)
ALOSDIS_(n)
DLOSDIS_(n)
REQEN_(n)
XX
X
0
相關PDF資料
PDF描述
MS3101A22-20S CONN RCPT 9POS FREE HNG W/SCKT
IDT72V263L10PFI8 IC FIFO 8192X18 10NS 80QFP
VI-B6B-IV-F1 CONVERTER MOD DC/DC 95V 150W
IDT72615L50PF8 IC FIFO BY SYNC 512X18X2 64QFP
MS27656T15F5PB CONN RCPT 5POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XRT73LC03AIVF 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Serial 120-Pin LQFP
XRT73LC03AIV-F 功能描述:外圍驅動器與原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73LC04A 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04A_08 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04AES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*