- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT75L02 (Exar Corporation) TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER PDF資料下載
參數資料
| 型號： | XRT75L02 |
| 廠商： | Exar Corporation |
| 英文描述： | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
| 中文描述： | 雙通道E3/DS3/STS-1線路接口單元，其抖動 |
| 文件頁數： | 14/50頁 |
| 文件大?。?/td> | 343K |
| 代理商： | XRT75L02 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
xr
REV. 1.0.3
XRT75L02
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
12
27
SDO
RxMON
I/O
Serial Data Output:
This pin serially outputs the contents of the specified Command Register during
Read Operations. The data is updated on the falling edge of the SClk and this
pin is tri-stated upon completion of data transfer.
N
OTE
:
If configured in Hardware Mode, this pin functions as RxMON.
97
RESET
I
Register Reset:
Setting this input pin "Low" causes to reset the contents of the Command Reg-
isters to their default settings and default operating configuration
N
OTE
:
This pin is internally pulled up.
28
INT
LOSMUT
I/O
INTERRUPT Output:
A transition to “Low” indicates that an interrupt has been generated. The inter-
rupt function can be disabled by setting the interrupt enable bit to “0” in the
Channel Control Register.
N
OTES
:
1.
In Hardware mode, this pin functions as LOSMUT.
2.
This pin will remain asserted “Low” until the interrupt is serviced.
JITTER ATTENUATOR INTERFACE
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
15
JA1
I
Jitter Attenuator Select 1:
In Hardware Mode, this pin along with the pin JA0 configures the Jitter Attenua-
tor as shown in the table.
N
OTE
:
This pin is internally pulled down.
16
JATx/Rx
I
Jitter Attenuator Path Select
In Hardware Mode, tie this pin “High” to select the Jitter Attenuator in the Trans-
mit Path . Connect this pin “Low” to select the Jitter Attenuator in the Receive
Path. This applies to all channels.
N
OTE
:
This pin is internally pulled down.
14
JA0
I
Jitter Attenuator Select 0:
In Hardware Mode, this pin along with pin JA1 configures the Jitter Attenuator
as shown in the above table.
N
OTE
:
This pin is internally pulled down.
MICROPROCESSOR SERIAL INTERFACE - (HOST MODE)
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
JA0
0
0
Mode
16 bit FIFO
32 bit FIFO
JA1
0
1
1
1
Disable Jitter
Attenuator
Disable Jitter
Attenuator
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75L02IV | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
| XRT75L03D | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L04D | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L04DIV | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L04 | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75L02DES | 功能描述:時鐘合成器/抖動清除器 2CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L02DIV-F | 功能描述:網絡控制器與處理器 IC 2-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT75L02DIVTR-F | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L02ES | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L02IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
發布緊急采購，3分鐘左右您將得到回復。